| 전자부품 데이터시트 검색엔진 |
|
SAA7380GP 데이터시트(PDF) 8 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
SAA7380GP 데이터시트(HTML) 8 Page - NXP Semiconductors |
|
8 / 60 page ![]() 1996 Apr 25 8 Philips Semiconductors Preliminary specification Error correction and host interface IC for CD-ROM (ELM) SAA7380 6.1 Pin functions 6.1.1 RA0 TO RA14 External memory address signals. 6.1.2 RA16/CAS External memory RA16 signal if SRAM or, CAS signal if DRAM. 6.1.3 RA15/RAS External memory RA15 signal if SRAM or, RAS signal if DRAM. 6.1.4 RWE Write output enable signal for external buffer memory. This is LOW when the SAA7380 wants to write data into the external memory. 6.1.5 RD0 TO RD7 External buffer memory bidirectional data signals. 6.1.6 SFSY Frame sync for the Q-to-W subcode, indicates when P-channel is available by a HIGH-to-LOW transition. Frame 0 is also indicated by no transition on this line. 6.1.7 RCK In response to SFSY going LOW data is clocked into the SAA7380 before each rising edge using this clock output. 6.1.8 SUB Q-to-W subcode is input in response to RCK in 3-wire EIAJ mode or WS in “V4” mode compatible with the SAA7345. 6.1.9 BCK Bit clock for the serial data input from the CD decoder. 6.1.10 WS Word clock for the serial data input from the CD decoder. 6.1.11 DATA Serial data input from the CD decoder. This may be either I2S-bus or EIAJ 16-bit format. 6.1.12 C2PO Error flag from the CD decoder. A HIGH indicates that a byte has not been corrected by the C2 error corrector and therefore is not valid. This is taken into account by the SAA7380 error corrector. 6.1.13 SDA Sub-CPU bidirectional data signal. This signal forms part of the 3-wire serial interface between the SAA7380 and the sub-CPU. 6.1.14 SCL Sub-CPU sync signal. This signal forms part of the 3-wire serial interface between the SAA7380 and the sub-CPU. This signal is used to synchronize data transfers between the sub-CPU and the SAA7380. 6.1.15 INT Sub-CPU interrupt signal. This active LOW output signals to the sub-CPU that the SAA7380 has an interrupt request. 6.1.16 RESET Forcing this input LOW resets the SAA7380. 6.1.17 SYN Sub-CPU clock signal. This signal forms part of the 3-wire serial interface between the SAA7380 and the sub-CPU. This signal is the sub-CPU driven bit clock used to synchronize the signals on the SDA line. 6.1.18 CS1/HEN In the ATAPI mode this is the host chip select 1 address signal. In the Sanyo and Oak compatibility modes setting this input LOW enables the host interface. 6.1.19 HWR This active LOW signal is the host write request. 6.1.20 HRD This active LOW signal is the host read request. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |