| 전자부품 데이터시트 검색엔진 |
|
SAA7780 데이터시트(PDF) 25 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
SAA7780 데이터시트(HTML) 25 Page - NXP Semiconductors |
|
25 / 70 page ![]() ThunderBird Q3D PCI Audio SAA7780 Accelerator Philips Semiconductors Product Specification 1999 Sep 30 25 Legend: C CMOS-compatible input AGND Analog ground DGND Digital ground pin I Input-only pin (can become bidirectional for test mode) IO Bidirectional pin O Output-only pin (can become bidirectional for test mode) APWR Analog power supply pin DPWR Digital power supply pin T TTL-compatible input PD Indicates a high-impedance with approximately 10 K¾ minimum resistance to VSS (internal pull-down resistor on pin) PU Indicates a high-impedance with approximately 10 K¾ minimum resistance to VDD (internal pull-up resis- tor on pin) PUB Inidcates that this pin needs an external pull-up resistor when the chip is installed on a board or tester. A 10K ohm resistor is nominal S Indicates a Schmitt-trigger input with hysteresis for noise immunity TS Three-state pin STS Sustained three-state output / TTL input (if applicable) OD Open drain pad A Analog based I/O. Use a pad with ESD protection CP Core power. Denotes a pad that supplies power for the core of the chip only CG Core ground. Denotes a pad that supplies ground to the core only RP Ring power. Denotes a pad that supplies power to the pads only RG Ring ground. Denotes a pad that supplies ground to the ring only RPD Ring power with option to power core level shifter. Denotes a pad that supplies power to the ring while its core side connector can optionally supply internal level shifters RCG Ring/core ground. Denotes a pad that supple a ground connection to the ring and core HZ High impedance. When in a three state test mode, this pin will be forced into a high impedance state NT Nand tree. When in a NAND tree test mode, this pin will be included in the parametric NAND tree logic NTO Nand tree output. When in a NAND tree test mode, this pin is the output of the parametric NAND tree FSB Function System Block test. Denotes that his pin is not timing critical and is available for FSB multiplexing VDD 1,142,28,41, 54,68,80,96, 112,121,135, 142 DPWR Ring Power VWELL 117 DPWR External N-Well Bias Tie these pins to 5V for proper 5 volt tolerant operation. The 5V supply must be powered up before the 3V supply. Likewise, the 3V supply must be powered down before the 5V supply. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |