TDA4886 datasheet(18/52 Pages) PHILIPS

18 / 52 page

1998 Nov 11

Philips Semiconductors

Product speciﬁcation

140 MHz video controller with I2C-bus

TDA4886

6. Pin 5 should be used for input clamping and blanking during vertical retrace (signal blanking, brightness blanking and

if control bit PEDST = 1 pedestal blanking). With a fast clamping pulse (transition between V5 = 1.2 to 3.5 V and vice

versa in less than 75 ns/V) no blanking will occur during input clamping.

For 75 ns/V < tr/f5 ≤ 280 ns/V the generation of the internal vertical blanking pulse is uncertain. For tr/f5 > 280 ns/V

the internal blanking pulse will be generated.

Pin 5 open-circuited will activate permanent input clamping and undefined blanking.

7. Pin 5 can be used to synchronize all adjustments via the I2C-bus (one by one). In case of a completed I2C-bus

transmission in buffered mode only the leading edge of a vertical blanking pulse activates an adjustment. See also

Section 7.10.

After the adjustment has been activated (validation of buffered I2C-bus data) the I2C-bus will be reset and further

transmissions in direct or buffered mode are enabled.

I2C-bus transmissions in direct mode need no synchronization pulses.

8. Input voltages less than

−0.1 V can produce internal substrate currents which disturb the leakage currents at the

signal inputs. An internal protection circuit creates a current for pin voltages of approximately 0 V or less. Feeding

clamping/blanking pulses via a resistor of some k

Ω protects the pin from negative voltages.

9. Pin 11 should be used for output clamping and/or blanking. Pin 11 open-circuited will activate permanent blanking

and output clamping.

10. Composite signals will not disturb normal operations because an internal clipping circuit cuts all signal parts below

input reference black level (see Fig.3).

11. Contrast control acts on internal colour signals under I2C-bus control; subaddress 02H (bit resolution 1.6% of

contrast range).

12.

An: colour signal output amplitude in channel n = 1, 2 or 3 at any contrast setting.

An0: colour signal output amplitude in channel n = 1, 2 or 3 at nominal contrast setting and same gain setting.

13. When OSD fast blanking is active and V2,3,4 are HIGH (V1 > 1.7 V, V2,3,4 > 1.7 V) the OSD colour signals will be

inserted in front of the gain potentiometers. This assures a correct grey scale of all video signals. The amplitudes of

the inserted OSD signals can be controlled simultaneously by OSD contrast via the I2C-bus.

14. OSD contrast control acts on inserted OSD colour signals under I2C-bus control; subaddress 03H (bit resolution

6.7% of OSD contrast range).

15. This pin can be used for subcontrast setting, beam current limiting and contrast modulation. Both the video and OSD

contrast are reduced simultaneously (see Figs 8 and 9). Because of the high-ohmic input impedance the pin should

be tied to a voltage of more than 5 V or applied with a capacitor of some nF if not used.

16. Brightness control adds an I2C-bus controlled DC offset to the internal colour signal; subaddress 01H (bit resolution

1.6% of brightness range).

17. The voltage difference between video black level and reference black level is related to the colour signal (see note 3)

with nominal 0.7 V (p-p) input signal, at nominal contrast (subaddress 02H = 26H) and for any gain setting.

The voltage difference (in Volts) is proportional to the gain setting (grey scale tracking). Therefore

∆V

bl (in percent)

is constant for any gain setting. The given values of

∆V

bl are valid only for video black levels higher than the signal

output switch-off voltage V22,19,16(min).

18. Gain control acts on video signals and inserted OSD video signals under I2C-bus control; subaddress 04H

(channel 1), 05H (channel 2) and 06H (channel 3; bit resolution 1.6% of gain range respectively).

∆G

track

maximum of

---------







log

---------







log

---------







log

;







TDA4886 데이터시트(PDF) 18 Page - NXP Semiconductors

TDA4886 데이터시트(HTML) 18 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

데이터시트 다운로드

링크 URL