| 전자부품 데이터시트 검색엔진 |
|
MYG 데이터시트(PDF) 4 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
MYG 데이터시트(HTML) 4 Page - List of Unclassifed Manufacturers |
|
4 / 4 page ![]() MYG Varistors Data Sheet Electrical Performance Characteristics Characteristics Test Method Specifications Standard test condition Environmental conditions under which every measuring is done without doubt on the measuring results. Unless specified, the temperature, and relative humidity should be 5 to 35 and 45 to 85% respectively. Varistor voltage The varistor voltage is measured with an impressed current of 1mA (exception, 5 :0.1mA) and serves to characterize each varistor type. To meet the specified value Maximum operating voltage The maximum sinusoidal RMS voltage or maximum DC voltage that can be applied continuously in the specified environmental temperature range. Maximum clamping voltage Maximum clamping voltage is the maximum voltage VP between two terminals with the specified standard impulse current IP (8/20µS). Withstanding surge current The maximum current within the varistor voltage change of ±10% with the standard impulse current (8/20µS) applied one or two times. Energy The maximum energy within the varistor voltage change of±10% when one impulse of 10/1000µs m-sec is applied. Rated power The maximum power that can be applied within the specified ambient temperature. Capacitance The capacitance of varistor is the typical value measured at 1 KHz, 1Vrms max, OV bias and 25±2 . Temperature Coefficient of varistor Voltage (VC at 85 - VC at 25 ) / (VC at 25 ) * 1 / 60 * 100 (%/ ) -0.05%/ max. Mechanical Performance Characteristics Characteristics Test Methods Specifications Robustness of Terminations (Tensile) After gradually applying the force specified below and keeping the unit fixed for ten seconds, the terminal shall be visually examined for any damage. Terminal diameter Force 0.6mm 9.8N (1.0kgf) 0.8mm 9.8N (1.0kgf) 1.0mm 19.6N (2.0kgf) Robustness of Terminations (Bending) The unit shall be secured with its terminal kept vertical and the force specified below be applied in the axial direction. The terminal shall gradually be bent by 90° in one direction, then 90 ° in the opposite direction, and again back to the original position. The damage of the terminal shall be visually examined. Terminal diameter Force 0.6mm 4.9N (0.5kgf) 0.8mm 4.9N (0.5kgf) 1.0mm 9.8N (1.0kgf) Vibration After repeatedly applying a single harmonic vibration (amplitude: 0.75 mm): double amplitude: 1.5 mm with 1 minute vibration frequency cycles (10 Hz to 55 Hz to 10 Hz) to each of three perpendicular directions for 2 hours. Thereafter, the unit shall be visually examined. No outstanding damage Solderability After dipping the terminals to a depth of approximately 3 mm from the body in a soldering bath of 235±5 for 2±0.5 seconds, the terminal shall be visually examined. Approximately 95% of the terminals shall be covered with solder uniformly. Resistance to Soldering Heat After each lead shall be dipped into a solder bath having a temperature 260±5 to a point 2.0 to 2.5 mm from the body of the unit, using shielding board (t=1.5mm), be held there for specified time (5 series: 5±1 s and others: 10±1 s), and then be stored at room temperature and humidity for 1 to 2 hours. The change of Vc and mechanical damages are examined. VcmA/VcmA ±5% No outstanding damage 4 |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |