| 전자부품 데이터시트 검색엔진 |
|
PIC16F688-E/ST 데이터시트(PDF) 65 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F688-E/ST 데이터시트(HTML) 65 Page - Microchip Technology |
|
65 / 174 page ![]() 2004 Microchip Technology Inc. Preliminary DS41203B-page 63 PIC16F688 8.0 ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE The analog-to-digital converter (A/D) allows conversion of an analog input signal to a 10-bit binary representa- tion of that signal. The PIC16F688 has eight analog inputs, multiplexed into one sample and hold circuit. The output of the sample and hold is connected to the input of the converter. The converter generates a binary result via successive approximation and stores the result in a 10-bit register. The voltage reference used in the conversion is software selectable to either VDD or a voltage applied by the VREF pin. Figure 8-1 shows the block diagram of the A/D on the PIC16F688. FIGURE 8-1: A/D BLOCK DIAGRAM 8.1 A/D Configuration and Operation There are three registers available to control the functionality of the A/D module: 1. ANSEL (Register 8-1) 2. ADCON0 (Register 8-2) 3. ADCON1 (Register 8-3) 8.1.1 ANALOG PORT PINS The ANS<7:0> bits (ANSEL<7:0>) and the TRIS bits control the operation of the A/D port pins. Set the corresponding TRIS bits to set the pin output driver to its high-impedance state. Likewise, set the corresponding ANSEL bit to disable the digital input buffer. 8.1.2 CHANNEL SELECTION There are eight analog channels on the PIC16F688, AN0 through AN7. The CHS<2:0> bits (ADCON0<4:2>) control which channel is connected to the sample and hold circuit. 8.1.3 VOLTAGE REFERENCE There are two options for the voltage reference to the A/D converter: either VDD is used, or an analog voltage applied to VREF is used. The VCFG bit (ADCON0<6>) controls the voltage reference selection. If VCFG is set, then the voltage on the VREF pin is the reference; otherwise, VDD is the reference. RA0/AN0 A/D RA1/AN1/VREF RA2/AN2 RC0/AN4 VDD VREF ADON GO/DONE VCFG = 1 VCFG = 0 CHS<2:0> ADRESH ADRESL 10 10 ADFM VSS RC1/AN5 RC2/AN6 RC3/AN7 RA4/AN3 Note: Analog voltages on any pin that is defined as a digital input may cause the input buffer to conduct excess current. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |