PIC18F44J10-ESLASHML datasheet(160/358 Pages) MICROCHIP

160 / 358 page

PIC18F45J10 FAMILY

DS39682C-page 158

Preliminary

SSPxCON2: MSSPx CONTROL REGISTER 2 (I2C™ MODE)

R/W-0

GCEN

ACKSTAT

ACKDT

ACKEN(1)

RCEN(1)

PEN(1)

RSEN(1)

SEN(1)

bit 7

bit 0

bit 7

GCEN: General Call Enable bit (Slave mode only)

= Enable interrupt when a general call address (0000h) is received in the SSPxSR

= General call address disabled

bit 6

ACKSTAT: Acknowledge Status bit (Master Transmit mode only)

= Acknowledge was not received from slave

= Acknowledge was received from slave

bit 5

ACKDT: Acknowledge Data bit (Master Receive mode only)

= Not Acknowledge

= Acknowledge

Note:

Value that will be transmitted when the user initiates an Acknowledge sequence at

the end of a receive.

bit 4

ACKEN: Acknowledge Sequence Enable bit (Master Receive mode only)(1)

= Initiate Acknowledge sequence on SDAx and SCLx pins and transmit ACKDT data bit.

Automatically cleared by hardware.

= Acknowledge sequence Idle

bit 3

RCEN: Receive Enable bit (Master mode only)(1)

= Enables Receive mode for I2C

= Receive Idle

bit 2

PEN: Stop Condition Enable bit (Master mode only)(1)

= Initiate Stop condition on SDAx and SCLx pins. Automatically cleared by hardware.

= Stop condition Idle

bit 1

RSEN: Repeated Start Condition Enable bit (Master mode only)(1)

= Initiate Repeated Start condition on SDAx and SCLx pins. Automatically cleared by

hardware.

= Repeated Start condition Idle

bit 0

SEN: Start Condition Enable/Stretch Enable bit(1)

In Master mode:

= Initiate Start condition on SDAx and SCLx pins. Automatically cleared by hardware.

= Start condition Idle

In Slave mode:

= Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)

= Clock stretching is disabled

Note 1: For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I2C module is not in the Idle mode,

these bits may not be set (no spooling) and the SSPxBUF may not be written (or

writes to the SSPxBUF are disabled).

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

PIC18F44J10-E/ML 데이터시트(PDF) 160 Page - Microchip Technology

PIC18F44J10-E/ML 데이터시트(HTML) 160 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL