| 전자부품 데이터시트 검색엔진 |
|
MIC2132YML 데이터시트(PDF) 26 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MIC2132YML 데이터시트(HTML) 26 Page - Microchip Technology |
|
26 / 48 page ![]() MIC2132 DS20006654B-page 26 2022 Microchip Technology Inc. and its subsidiaries FIGURE 4-12: EN Pin Sequencing. When the EN pin voltage is below the lower EN thresh- old, the MIC2132 goes into Shutdown mode. When in Shutdown mode, the MIC2132 stops switching and all internal control circuitry switches off to reduce the quies- cent current. The EN pin, along with the PG pin, can be used for sequencing multiple MIC2132 devices. It is recommended to power up VIN before the EN signal. 4.5.9 ADAPTIVE VOLTAGE POSITIONING (AVP), ALSO KNOWN AS DROOP FUNCTION (RECOMMENDED FOR CCM ONLY) In some high-current applications, a requirement on a precisely controlled output impedance is imposed. This dependence of output voltage on load current is often termed, “droop”, “load line” regulation, or Adaptive Voltage Positioning (AVP). The basic functionality of the AVP function is to achieve a controlled output resistance for the buck regulator, so that at 0A load, the output is +Ɛ% higher than the nom- inal voltage and at maximum load, the output is -Ɛ% related to the nominal output value, as shown in Figure 4-13. FIGURE 4-13: AVP Ideal Output Resistive Characteristic. It is necessary to achieve the resistive characteristic above over the full frequency range of output loads. FIGURE 4-14: VOUT Load Transient Error without AVP/DROOP. FIGURE 4-15: VOUT Load Transient Error with AVP/DROOP. Figure 4-14 and Figure 4-15 explain how the AVP design window of ±Ɛ can be used to reduce the amount of the output capacitor necessary to sustain the load transient. Alternatively, the AVP can be used to improve the error of the load transient if it is decided to keep the same output capacitor. The DROOP pin is an analog output, which provides a voltage proportional with the output current in CCM, according to the formula in Equation 4-20. EQUATION 4-20: EN PVDD/VDD VDD UVLO Bias ready VOUT 5V Bypass VIN VOUT OUTPUT CURRENT (A) 0A IOUT(MAX) ΔVOUT = VOUT × 2ε VOUT(DC) VOUT(DC) Where: VCSH = Voltage at CSH Pin in CCM RSENSE = Current Sensing Resistance IL = Inductor Current per Phase VDROOP = VCSH – 1.2V = 8 × RSENSE × IL |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |