ADC10732CIWM datasheet(7/29 Pages) NSC

7 / 29 page

Electrical Characteristics (Continued)

The following specifications apply for V

+ =AV+ =DV+ = +5.0 V

DC,VREF+ = 2.5 VDC,VREF− = GND, VIN− = 2.5V for Signed

Characteristics, V

IN− = GND for Unsigned Characteristics and fCLK = 2.5 MHz unless otherwise specified. Boldface limits ap-

ply for T

A =TJ =TMIN to TMAX; all other limits TA =TJ = +25˚C. (Notes 8, 9, 10)

Symbol

Parameter

Conditions

Typical

(Note 11)

Limits

(Note 12)

Units

(Limits)

AC CHARACTERISTICS

SCS

CS Set-Up Time, Set-Up Time from

Falling Edge of CS to Rising Edge of

Clock

ns (min)

(1 t

CLK

−14ns)

(1 t

CLK

−30ns)

(max)

SDI

DI Set-Up Time, Set-Up Time from

Data Valid on DI to Rising Edge of

Clock

ns (min)

HDI

DI Hold Time, Hold Time of DI Data

from Rising Edge of Clock to Data not

Valid on DI

ns (min)

DO Access Time from Rising Edge of

CLK When CS is “Low” during a

Conversion

ns (min)

DO or SARS Access Time from CS ,

Delay from Falling Edge of CS to Data

Valid on DO or SARS

ns (max)

DSARS

Delay from Rising Edge of Clock to

Falling Edge of SARS when CS is

“Low”

100

200

ns (max)

HDO

DO Hold Time, Hold Time of Data on

DO after Falling Edge of Clock

ns (max)

DO Access Time from Clock, Delay

from Falling Edge of Clock to Valid

Data of DO

ns (max)

1H,t0H

Delay from Rising Edge of CS to DO

or SARS TRI-STATE

ns (max)

DCS

Delay from Falling Edge of Clock to

Falling Edge of CS

ns (min)

CS(H)

CS “HIGH” Time for A/D Reset after

Reading of Conversion Result

1 CLK

cycle (min)

CS(L)

ADC10731 Minimum CS “Low” Time to

Start a Conversion

1 CLK

cycle (min)

Time from End of Conversion to CS

Going “Low”

5 CLK

cycle (min)

Delay from Power-Down command to

10% of Operating Current

1µs

Delay from Power-Up Command to

Ready to Start a New Conversion

µs

Capacitance of Logic Inputs

OUT

Capacitance of Logic Outputs

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.

Note 2: All voltages are measured with respect to GND, unless otherwise specified.

Note 3: Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and

test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions.

Note 4: When the input voltage (VIN) at any pin exceeds the power supplies (VIN < GND or VIN > AV

+ or DV+), the current at that pin should be limited to 30 mA.

The 120 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 30 mA to four.

Note 5: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax, θJA and the ambient temperature, TA. The maximum

allowable power dissipation at any temperature is PD =(TJmax −TA)/θJA or the number given In the Absolute Maximum Ratings, whichever is lower. For this device,

TJmax = 150˚C. The typical thermal resistance (θJA) of these Paris when board mounted can be found in the following table:

ADC10732CIWM 데이터시트(PDF) 7 Page - National Semiconductor (TI)

ADC10732CIWM 데이터시트(HTML) 7 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

데이터시트 다운로드

링크 URL