ISO7220AD datasheet(4/25 Pages) TI

4 / 25 page

www.ti.com

ELECTRICAL CHARACTERISTICS

SWITCHING CHARACTERISTICS

ISO7220A, ISO7220C, ISO7220M

ISO7221A, ISO7221C, ISO7221M

SLLS755F – JULY 2006 – REVISED AUGUST 2007

VCC1 and VCC2 at 5-V operatjion, over recommended operating conditions (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

SUPPLY CURRENT

ISO7220A, ISO7220C, ISO7220M

Quiescent

VI = VCC or 0 V, no load

ISO7221A, ISO7221C, ISO7221M

8.5

ISO7220A

ICC1

1 Mbps

VI = VCC or 0 V, no load

ISO7221A

ISO7220C, ISO7220M

25 Mbps

VI = VCC or 0 V, no load

ISO7221C, ISO7221M

ISO7220A, ISO7220C, ISO7220M

Quiescent

VI = VCC or 0 V, no load

ISO7221A, ISO7221C, ISO7221M

8.5

ISO7220A

ICC2

1 Mbps

VI = VCC or 0 V, no load

ISO7221A

ISO7220C, ISO7220M

25 Mbps

VI = VCC or 0 V, no load

ISO7221C, ISO7221M

IOH = –4 mA, See Figure 1

VCC – 0.8

4.6

VOH

High-level output voltage

IOH = –20 μA, See Figure 1

VCC – 0.1

IOL = 4 mA, See Figure 1

0.2

0.4

VOL

Low-level output voltage

IOL = 20 μA, See Figure 1

0.1

VI(HYS) Input voltage hysteresis

150

IIH

High-level input current

IN from 0 V to VCC

μA

IIL

Low-level input current

–10

Input capacitance to ground

IN at VCC, VI = 0.4 sin (4E6πt)

CMTI

Common-mode transient immunity

VI = VCC or 0 V, See Figure 3

kV/

μs

VCC1 and VCC2 at 5-V operation, over recommended operating conditions (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

tpLH,

Propagation delay

280

405

475

tpHL

ISO722xA

PWD

Pulse-width distortion |tpHL – tpLH|

(1)

tpLH,

Propagation delay

tpHL

ISO722xC

See Figure 1

PWD

Pulse-width distortion |tpHL – tpLH|

(1)

tpLH,

Propagation delay

tpHL

ISO722xM

PWD

Pulse-width distortion |tpHL – tpLH|

(1)

0.5

ISO722xA

180

tsk(pp)

Part-to-part skew (2)

ISO722xC

ISO722xM

ISO7220A

tsk(o)

Channel-to-channel output skew (3)

ISO7220C/M

0.2

Output signal rise time

See Figure 1

Output signal fall time

tfs

Failsafe output delay time from input power loss

See Figure 2

μs

(1)

Also referred to as pulse skew.

(2)

tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices

operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.

(3)

tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the

same direction while driving identical specified loads.

Submit Documentation Feedback

ISO7220AD 데이터시트(PDF) 4 Page - Texas Instruments

ISO7220AD 데이터시트(HTML) 4 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

데이터시트 다운로드

링크 URL