MPC8280 datasheet(275/1386 Pages) FREESCALE

275 / 1386 page

60x Signals

MPC8280 PowerQUICC II Family Reference Manual, Rev. 1

Freescale Semiconductor

7-17

7.2.8.3.1

Partial Data Valid (PSDVAL)—Input

Following are the state meaning and timing comments for the PSDVAL input signal. Note that TA asserts

with PSDVAL to indicate the termination of the current transfer and for each complete data beat in burst

transactions.

State Meaning

Asserted—Indicates that a beat data transfer completed successfully. Note that

PSDVAL must be asserted for each data beat in a single beat, port size and burst

transaction,. For more information, see Section 8.5.5, “Port Size Data Bus

Transfers and PSDVAL Termination.”

Negated—(During DBB) indicates that, until PSDVAL is asserted, the MPC8280

must continue to drive the data for the current write or must wait to sample the data

for reads.

Timing Comments

Assertion—Must not occur before AACK for the current transaction (if the

address retry mechanism is to be used to prevent invalid data from being used by

the MPC8280); otherwise, assertion may occur at any time during the assertion of

DBB. The system can withhold assertion of PSDVAL to indicate that the

MPC8280 should insert wait states to extend the duration of the data beat.

Negation—Must occur after the bus clock cycle of the final (or only) data beat of

the transfer. For a burst and/or port size transfer, the system can assert PSDVAL

for one bus clock cycle and then negate it to insert wait states during the next beat.

(Note: when the MPC8280 processor is configured for 1:1 clock mode and is

performing a burst read into the data cache, the MPC8280 requires two wait state

between the assertion of TS and the first assertion of PSDVAL for that transaction,

or 1 wait state for 1.5:1 clock mode.)

7.2.8.3.2

Partial Data Valid (PSDVAL)—Output

Following are the state meaning and timing comments for PSDVAL as an output signal.

State Meaning

Asserted—Indicates that the data has been latched for a write operation, or that the

data is valid for a read operation, thus terminating the current data beat. If it is the

last or only data beat, this also terminates the data tenure.

Negated—Indicates that the master must extend the current data beat (insert wait

states) until data can be provided or accepted by the MPC8280.

Timing Comments

Assertion—Occurs on the clock in which the current data transfer can be

completed.

Negation—Occurs after the clock cycle of the final (or only) data beat of the

transfer. For a burst transfer, PSDVAL may be negated between beats to insert one

or more wait states before the completion of the next beat.

MPC8280 데이터시트(PDF) 275 Page - Freescale Semiconductor, Inc

MPC8280 데이터시트(HTML) 275 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL