| 전자부품 데이터시트 검색엔진 |
|
PCM1737E/2K.B 데이터시트(PDF) 16 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
PCM1737E/2K.B 데이터시트(HTML) 16 Page - Texas Instruments |
|
16 / 32 page ![]() ® 16 PCM1737 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Register 18 R/W IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 res OVER res INZD ATLD ATTS MUT2 MUT1 R/W Read/Write Mode Select When R/W = 0, a Write operation is performed. When R/W = 1, a Read operation is performed. Default Value: 0 MUTx Soft Mute Control Where, x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR ( x = 2). These bits are Read/Write. Default Value: 0 MUTx = 0 Mute Disabled (default) MUTx = 1 Mute Enabled The mute bits, MUT1 and MUT2, are used to enable or disable the Soft Mute function for the corresponding DAC outputs, VOUTL and VOUTR. The Soft Mute function is incorporated into the digital attenuators. When Mute is disabled (MUTx = 0), the attenuator and DAC operate normally. When Mute is enabled by setting MUTx = 1, the digital attenuator for the corresponding output will be decremented from the current setting to the infinite attenuation, one attenuator step (0.5dB) at a time, with the rate of change programmed by the ATTS bit. This provides ‘pop-free’ muting of the DAC output. By setting MUTx = 0, upon returning from Soft Mute, the attenuator will be incremented one step at a time to the previously-programeed attenuator level. ATTS Attenuation Rate Select This bit is Read/Write. Default Value: 0 ATTS = 0 Attenuation rate is 2/fS (default) ATTS = 1 Attenuation rate is 4/fS Changes in attenuator levels are made by incrementing or decrementing the attenuator by one step (0.5dB) for every 2/fS or 4/fS time interval until the programmed attenuator setting is reached. This helps to minimize audible ‘clicking’, or zipper noise while the attenuator is changing levels. The ATTS bit allows the user to select the rate at which the attenuator is decremented/incremented during level transitions. ATLD Attenuation Control This bit is Read/Write. Default Value: 0 ATLD = 0 Attenuator Disabled (default) ATLD = 1 Attenuator Enabled The ATLD bit must be set to logic ‘1’ in order for the attenuators to function. Setting ATLD to logic ‘0’ will disable the attenuator function and cause the current attenuator data to be lost. Set ATLD = 1 immediately after reset. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |