| 전자부품 데이터시트 검색엔진 |
|
AMC0X11R 데이터시트(PDF) 16 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
AMC0X11R 데이터시트(HTML) 16 Page - Texas Instruments |
|
16 / 32 page ![]() 7.3.2 Isolation Channel Signal Transmission As shown in Figure 7-1, the AMC0x11R uses an on-off keying (OOK) modulation scheme to transmit the modulator output bitstream across the SiO2-based isolation barrier. The transmit driver (TX) is illustrated in the Functional Block Diagram . TX transmits an internally generated, high-frequency carrier across the isolation barrier to represent a digital one. However, TX does not send a signal to represent a digital zero. The nominal frequency of the carrier used inside the AMC0x11R is 480MHz. The receiver (RX) on the other side of the isolation barrier recovers and demodulates the signal and provides the input to the analog filter. The AMC0x11R transmission channel is optimized to achieve the highest level of common-mode transient immunity (CMTI) and the lowest level of radiated emissions. The high-frequency carrier and RX/TX buffer switching cause these emissions. Modulator Bitstream on High-side Internal Clock Signal Across Isolation Barrier Recovered Sigal on Low-side Figure 7-1. OOK-Based Modulation Scheme 7.3.3 Analog Output The AMC0x11R provides a single-ended analog output voltage proportional to the input voltage. The output is referred to GND2 and is galvanically isolated from the input of the device. The output is designed to connect directly to the input of an ADC. The full-scale output voltage is set by the REFIN pin. For any input voltage within the specified linear input range, the device outputs a voltage equal to: VOUT = VIN / VClipping x VREFIN = (VINP – VSNSN) / VClipping x VREFIN (1) Connect REFIN to the same reference voltage as the ADC to match the ADC dynamic input voltage range. With a shared reference voltage, the ADC outputs a positive full-scale code when the clipping voltage is applied to the input of the AMC0x11R. The output buffer requires a minimum headroom of 250mV against GND2 for linear operation. Therefore, the device shows non-linear behavior for input voltages near 0V. Calculate the minimum input voltage for linear operation as follows: VINP, MIN = (250mV x VClipping) / VREFIN (2) For example, the minimum linear input voltage for the AMC0x11R device with a clipping voltage of 2.56V and VREFIN = 5V, is 128mV. The device is linear within the specified linear full-scale range. Beyond the linear full-scale range, the output continues to follow the input, but with reduced linearity performance. The output clips when the input voltage reaches the clipping voltage. Figure 7-2 shows the input-to-output transfer characteristic. AMC0211R, AMC0311R SBASAR1 – JULY 2025 www.ti.com 16 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: AMC0211R AMC0311R |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |