 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
L99VR02XP 데이터시트(PDF) 25 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L99VR02XP 데이터시트(HTML) 25 Page - STMicroelectronics |
|
|
25 / 50 page  Figure 42. Example of output voltage selection Co1 VS_LDO1 En_LDO1 Ishort_LDO1 RES_LDO2 SEL1_LDO1 OUT_LDO1 Vcw_LDO1 Wi_LDO1 GND SEL2_LDO1 TW_LDO2 SEL3_LDO1 RES_LDO1 En_LDO2 OUT_LDO2 SEL1_LDO2 SEL2_LDO2 SEL3_LDO2 Ishort_LDO2 TW_LDO1 TC_CONF VS_LDO2 VCR_LDO1 VCR_LDO2 Vcw_LDO2 Rsh_LDO2 Rsh_LDO1 Wi_LDO2 Ctr1 Ctr2 C1 C2 Ctw1 Ctw2 Co2 Rrst2 Rrst1 Vbat Ren2 Ren1 Vs1 Vs2 Vo2=2.5V Vo1=2.5V The SELx_LDOy pins are internally connected to GND via pull-down current source. 4.4 Enable The L99VR02XP is enabled/disabled by two independently enable inputs; a high voltage signal switches the regulator ON. When the enabled pins are set to low, the outputs are switched-off, the current consumption of the device becomes as low as 1 μA and the fast output discharge circuit is activated. It may happen that the enable pins must be driven by components supplied at a voltage different from the regulator supply voltage. In this case the EN_LDO1,2 input pins must be set high only once VS > 1.5 V. A solution to drive the enable pin is depicted in the Figure 43. Figure 43. Typical example of enable control VS_LDO1 En_LDO1 Ishort_LDO1 RES_LDO2 SEL1_LDO1 OUT_LDO1 Vcw_LDO1 Wi_LDO1 GND SEL2_LDO1 TW_LDO2 SEL3_LDO1 RES_LDO1 En_LDO2 OUT_LDO2 SEL1_LDO2 SEL2_LDO2 SEL3_LDO2 Ishort_LDO2 TW_LDO1 TC_CONF VS_LDO2 VCR_LDO1 VCR_LDO2 Vcw_LDO2 Rsh_LDO2 Rsh_LDO1 Wi_LDO2 Ctr1 Ctr2 C1 C2 Ctw1 Ctw2 Co2 Rrst2 Rrst1 Co1 Power supply - supply line 1 Ren1 Ren2 Enable supply - supply line 2 Power supply - supply line 1 Enable supply - supply line 3 In any case, since the enable input voltage is linked to the maximum dc supply voltage (VS_LDOy) applied to the L99VR02XP (-0.3 V ≤ VEN_LDO1,2 ≤ + 28 V), special care must be adopted in driving EN_LDO1,2 pins to avoid exceeding the absolute maximum rating. External resistances in a range of 1 kΩ through 33 kΩ can be connected to the EN pins to further limit the current flow. L99VR02XP Application information DS14686 - Rev 1 page 25/50 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
