Table 5. Electrical characteristics at VCC = 3.3 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified)

Symbol

Parameter

Test conditions (1)

Min.

Typ.

Max.

Unit

VIO

Input offset voltage

TS3021A

0.5

2

mV

TS3021

0.5

6

-40 °C < Tamb < 125 °C, TS3021A

4

-40 °C < Tamb < 125 °C, TS3021

7

ΔVio/ΔT

Input offset voltage drift

-40 °C < Tamb < 125 °C

3

20

µV/°C

IIO

Input offset current (2)

Tamb

1

20

nA

-40 °C < Tamb < 125 °C

100

IIB

Input bias current (2)

Tamb

86

160

-40 °C < Tamb < 125 °C

300

ICC

Supply current

No load, output high, Vicm = 0 V

75

90

µA

No load, output high, Vicm = 0 V,

-40 °C < Tamb < 125 °C

120

No load, output low, Vicm = 0 V

86

110

No load, output low, Vicm = 0 V,

-40 °C < Tamb < 125 °C

125

ISC

Short-circuit current

Source

26

mA

Sink

24

VOH

Output voltage high

Isource = 1 mA

3.20

3.25

V

-40 °C < Tamb < 125 °C

3.10

VOL

Output voltage low

Isink = 1 mA

40

80

mV

-40 °C < Tamb < 125 °C

150

CMRR

Common mode rejection

ratio

0 < Vicm < 3.3 V

75

dB

SVR

Supply voltage rejection

∆Vcc = 2 to 5 V

58

73

TPLH

Propagation delay, low to

high output level (3)

Vicm = 0 V, f = 10 kHz, CL = 50 pF,

overdrive = 100 mV

39

65

ns

Vicm = 0 V, f = 10 kHz, CL = 50 pF,

overdrive = 20 mV

50

85

TPHL

Propagation delay, high to

low output level (4)

Vicm = 0 V, f = 10 kHz, CL = 50 pF,

overdrive = 100 mV

41

65

Vicm = 0 V, f = 10 kHz, CL = 50 pF,

overdrive = 20 mV

51

80

TF

Fall time

f = 10 kHz, CL = 50 pF, RL = 10 kΩ,

overdrive = 100 mV

5

TR

Rise time

f = 10 kHz, CL = 50 pF, RL = 10 kΩ,

overdrive = 100 mV

7

1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed at the

temperature range limits

2. Maximum values include unavoidable inaccuracies of the industrial tests

3. Response time is measured 10%/90% of the final output value with the following conditions: inverting input voltage (IN-) = Vicm and non-

inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive.

4. Response time is measured 10%/90% of the final output value with the following conditions: Inverting input voltage (IN-) = Vicm and non-

inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive.

TS3021, TS3021A

Electrical characteristics

DS4807 - Rev 11

page 5/17