전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

VNH5200ASTR-E 데이터시트(PDF) 19 Page - STMicroelectronics

부품명 VNH5200ASTR-E
상세설명  Fully integrated H-bridge motor driver for automotive applications
PDF  31 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  STMICROELECTRONICS [STMicroelectronics]
홈페이지  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

VNH5200ASTR-E 데이터시트(HTML) 19 Page - STMicroelectronics

Back Button VNH5200ASTR-E Datasheet HTML 15Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 16Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 17Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 18Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 19Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 20Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 21Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 22Page - STMicroelectronics VNH5200ASTR-E Datasheet HTML 23Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 19 / 31 page
background image
DocID023424 Rev 9
19/31
VNH5200AS-E
Application information
30
Figure 10. Behavior in fault condition (how a fault can be cleared)
Note:
In case the fault condition is not removed, the procedure for unlatching and sending the
device in Stby mode is:
- Clear the fault in the device (toggle: INA if ENA = 0 or INB if ENB =0)
- Pull low all inputs and Diag/EN pins within tDEL.
If the Diag/En pins are already low the fault can be cleared simply by toggling the input. The
device enters in stby mode as soon as the fault is cleared.
3.1
Reverse battery protection
Three possible solutions can be considered:
•
A Schottky diode D connected to VCC pin
•
An N-channel MOSFET connected to the GND pin (see Figure 9: Typical application
circuit)
•
A P-channel MOSFET connected to the VCC pin
The device sustains no more than -15 A in reverse battery conditions because of the two
Body diodes of the Power MOSFETs. Additionally, in reverse battery condition the I/Os of
VNH5200AS-E is pulled down to the VCC line (approximately -1.5 V).
Series resistor must be inserted to limit the current sunk from the microcontroller I/Os. If
IRmax is the maximum target reverse current through microcontroller I/Os, series resistor is:
R
V
IOs
V
CC
–
I
Rmax
---------------------------------
=



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com