INA206, INA207, INA208

SBOS360F – JUNE 2006 – REVISED NOVEMBER 2015

www.ti.com

Electrical Characteristics: Comparator (continued)

At TA = 25°C, VS = 12 V, VIN+ = 12 V, VSENSE = 100 mV, RL = 10 kΩ to GND, RPULL-UP = 5.1 kΩ each connected from CMP1

OUT and CMP2 OUT to VS, unless otherwise noted.

PARAMETERS

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Comparator 2 Delay Equation (5)

CDELAY = tD/5

µF

Comparator 2 Delay, tD

CDELAY = 0.1 μF

0.5

s

(5)

The Comparator 2 delay applies to both rising and falling edges of the comparator output.

7.7 Electrical Characteristics: Reference

At TA = 25°C, VS = 12 V, VIN+ = 12 V, VSENSE = 100 mV, RL = 10 kΩ to GND, RPULL-UP = 5.1 kΩ each connected from CMP1

OUT and CMP2 OUT to VS, unless otherwise noted.

PARAMETERS

TEST CONDITIONS

MIN

TYP

MAX

UNIT

REFERENCE VOLTAGE

1.2VREFOUT Output Voltage

1.188

1.2

1.212

V

dVOUT/dT

Reference Drift

TA = –40°C to 85°C

40

100

ppm/°C

0.6VREF Output Voltage

0.6

V

(Pins 3 and 6 of 14-pin packages

only)

dVOUT/dT

Reference Drift

TA = –40°C to 85°C

40

100

ppm/°C

dVOUT/dILOA

LOAD REGULATION

D

Sourcing

0 mA < ISOURCE < 0.5 mA

0.4

2

mV/mA

Sinking

0 mA < ISINK < 0.5 mA

0.4

mV/mA

ILOAD

LOAD CURRENT

TA = –40°C to 125°C

1

mA

dVOUT/dVS

LINE REGULATION

2.7 V < VS < 18 V, TA = –40°C to 125°C

30

µV/V

CAPACITIVE LOAD

Reference Output Maximum

No Sustained Oscillations

10

nF

Capacitive Load

OUTPUT IMPEDANCE

Pins 3 and 6 of 14-Pin Packages

10

k

Ω

Only

7.8 Electrical Characteristics: General

At TA = 25°C, VS = 12 V, VIN+ = 12 V, VSENSE = 100 mV, RL = 10 kΩ to GND, RPULL-UP = 5.1 kΩ each connected from CMP1

OUT and CMP2 OUT to VS, and CMP1 IN+ = 1 V and CMP2 IN– = GND, unless otherwise noted.

PARAMETERS

TEST CONDITIONS

MIN

TYP

MAX

UNIT

POWER SUPPLY

VS

Operating Power Supply

TA = –40°C to 125°C

2.7

18

V

Quiescent Current

VOUT = 2 V

1.8

2.2

mA

IQ

Quiescent Current over Temperature

VSENSE = 0 mV, TA = –40°C to 125°C

2.8

mA

Comparator Power-On Reset

1.5

V

Threshold (1)

TEMPERATURE

Specified Temperature Range

–40

125

°C

Operating Temperature Range

–55

150

°C

Storage Temperature Range

–65

150

°C

MSOP-10 Surface-Mount

200

°C/W

θJA

Thermal Resistance

SO-14, TSSOP-14 Surface-Mount

150

°C/W

(1)

The INA206, INA207, and INA208 are designed to power-up with the comparator in a defined reset state as long as CMP1 RESET is

open or grounded. The comparator will be in reset as long as the power supply is below the voltage shown here. The comparator will

assume a state based on the comparator input above this supply voltage. If CMP1 RESET is high at power-up, the comparator output

comes up high and requires a reset to assume a low state, if appropriate.

8

Submit Documentation Feedback

Copyright © 2006–2015, Texas Instruments Incorporated

Product Folder Links: INA206 INA207 INA208