전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

PCM1840 데이터시트(PDF) 28 Page - Texas Instruments

부품명 PCM1840
상세설명  PCM1840 Quad Channel, 32-Bit, 192-kHz, Burr-BrownTM Audio ADC
PDF  41 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  TI2 [Texas Instruments]
홈페이지  https://www.ti.com
Logo TI2 - Texas Instruments

PCM1840 데이터시트(HTML) 28 Page - Texas Instruments

Back Button PCM1840 Datasheet HTML 24Page - Texas Instruments PCM1840 Datasheet HTML 25Page - Texas Instruments PCM1840 Datasheet HTML 26Page - Texas Instruments PCM1840 Datasheet HTML 27Page - Texas Instruments PCM1840 Datasheet HTML 28Page - Texas Instruments PCM1840 Datasheet HTML 29Page - Texas Instruments PCM1840 Datasheet HTML 30Page - Texas Instruments PCM1840 Datasheet HTML 31Page - Texas Instruments PCM1840 Datasheet HTML 32Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 28 / 41 page
background image
28
PCM1840
SBAS989 – APRIL 2019
www.ti.com
Product Folder Links: PCM1840
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Typical Application (continued)
8.2.1 Design Requirements
Table 21 lists the design parameters for this application.
Table 21. Design Parameters
KEY PARAMETER
SPECIFICATION: 3.3-V AVDD OPERATION
AVDD
3.3 V
AVDD supply current consumption
> 23 mA (PLL on, four-channel recording, fS = 48 kHz)
IOVDD
1.8 V or 3.3 V
Maximum MICBIAS current
10 mA (MICBIAS voltage is the same as VREF)
8.2.2 Detailed Design Procedure
This section describes the necessary steps to configure the PCM1840 for this specific application. The following
steps provide a sequence of items that must be executed in the time between powering the device up and
reading data from the device or transitioning from one mode to another mode of operation.
1. Apply power to the device:
a. Power-up the IOVDD and AVDD power supplies, keeping the SHDNZ pin voltage low
b. The device now goes into hardware shutdown mode (ultra-low-power mode < 1 µA)
2. Transition from hardware shutdown mode to active mode whenever required for the recording operation:
a. Connect the MSZ, FMT0, and FMT1 pins voltage low to configure the device in 4-channel TDM slave
mode
b. Release SHDNZ only when the IOVDD and AVDD power supplies settle to the steady-state operating
voltage
c. Apply FSYNC and BCLK with the desired output sample rates and the BCLK to FSYNC ratio
This specific step can be done at any point in the sequence after step a
See the Phase-Locked Loop (PLL) and Clock Generation section for supported sample rates and the
BCLK to FSYNC ratio
d. The device recording data are now sent to the host processor via the TDM audio serial data bus
3. Assert the SHDNZ pin low to enter hardware shutdown mode (again) at any time
4. Follow step 2 onwards to exit hardware shutdown mode (again)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com