TLC5948APWPR.B datasheet(32/54 Pages) TI2

32 / 54 page

TLC5948A

SBVS192A – MARCH 2012 – REVISED DECEMBER 2012

www.ti.com

Table 10. Function Control Data Latch Bit Description (continued)

DEFAULT

BIT

VALUE

NUMBER

NAME

(Binary)

DESCRIPTION

Invisible detection mode (IDM) enable bit

0 = Disabled, 1 = Enabled

When this bit is '0', IDM is disabled. Therefore, LOD and LSD check the status

of the LEDs only at power-up.

When this bit is '1', LOD and LSD check the LED status with very small current

129

IDMENA

—

sinking at OUTn in a specific display segment. LOD and LSD can be checked

even if OUTn is off. The current value is set by the IDMCUR bits (bits[132:131])

and the time is set by the LATTMG bits (bits[128:127]) in the function control

data latch. Furthermore, the IDM operation is repeated every display period

with auto display mode enabled when the IDMRPT bit (bit 130) is set to '1'.

When the device is powered on, this bit is random.

Invisible detection mode (IDM) repeat bit

0 = Not repeated, 1 = Repeat

When this bit is '0', IDM is not repeated. Therefore, LOD and LSD check the

status of the LEDs once after the BLANK bit is changed from '1' to '0'.

Otherwise, LAT is input for a GS write when TMGRST is '1' or the GS counter

130

IDMRPT

—

is reset at power-up once at the time programmed by LATTMG. IDM is disabled

when IDMENA is set to '0' even if this bit is '1'.

When this bit is '1', IDM operation is repeated every display period with the auto

display mode enabled. LOD and LSD check the LED status at OUTn every

display period even if OUTn is off. When the device is powered on, this bit is

random.

Invisible detection mode (IDM) current select bits

The OUTn sink current for IDM can be selected with these bits. Refer to

131, 132

IDMCUR

—

Table 14 for the IDM sink current truth table. When the device is powered on,

these bits are random.

Output leak detection mode (OLD) enable bit

0 = Disabled, 1 = Enabled

When this bit is '0', output leak detection (OLD) is not checked and all OLD bits

in the status information data (SID) are set to '0'. OLD data are loaded into the

OLD data latch at the 65,535th GS clock. OLD data in SID may show the result

of the previous display period, depending on the LAT input timing.

133

OLDENA

—

When this bit is '1', OLD checks the LED status with a small current sourced

through OUTn in a display segment. OLD only checks OUTn with GS data set

to '0'. When OUTn current leakage is detected, the OLD bit that corresponds to

the leaking output is set to '1' in the SID. When IDMENA is '1', OLD operation is

disabled even if the OLDENA bit is set to '1' because OLD cannot get a correct

result when IDM is enabled. When the device is powered on, this bit is random.

Power-save mode (PSM) selection bits

The power-save mode is selected with these bits. Refer to Table 15 and

134-136

PSMODE

111

Table 16 for the PSM truth tables. When the device is powered on, these bits

are all set to '1'.

Submit Documentation Feedback

Product Folder Links: TLC5948A

TLC5948APWPR.B 데이터시트(PDF) 32 Page - Texas Instruments

TLC5948APWPR.B 데이터시트(HTML) 32 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

데이터시트 다운로드

링크 URL