| 전자부품 데이터시트 검색엔진 |
|
TMP411CD 데이터시트(PDF) 24 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMP411CD 데이터시트(HTML) 24 Page - Texas Instruments |
|
24 / 61 page ![]() 2.4V t (sec) VS (V) 2.7V To 5.5V t (sec) Vout_ADC (V) Undervoltage lockout TMP411 Supply Voltage range 1.6V POR Figure 7-2. Undervoltage Lockout Behavior (Legacy Chip) 2.45V t (sec) VS (V) 2.7V To 5.5V Vout_ADC (V) Undervoltage lockout TMP411 Supply Voltage range 1.23V POR t (sec) Figure 7-3. Undervoltage Lockout Behavior (New Chip) 7.3.7 Filtering Remote junction temperature sensors are typically implemented in a noisy environment. Noise is often created by fast digital signals that corrupt measurements. The TMP411/TMP411D has a built-in 65kHz filter on the D+ and D− inputs to minimize the effects of noise. TI recommends placing a bypass capacitor differentially across the sensor inputs to protect the application against unwanted coupled signals. The value of the capacitor must be between 100pF and 1nF. Some applications have better overall accuracy with additional series resistance, however, this increased accuracy is specific to the setup. When series resistance is added, the value must not be greater than 3kΩ. If filtering is needed, TI recommends component values of 100pF and 50Ω on each input. Exact values are specific to the application. 7.4 Device Functional Modes 7.4.1 Shutdown Mode (SD) The TMP411/TMP411D shutdown mode saves maximum power by shutting down all device circuitry other than the serial interface, which reduces current consumption to typically less than 3μA (0.6μA for TMP411 new chip and TMP411D); see Figure 6-20 (Figure 6-21 for new chip). Shutdown mode is enabled when the shutdown bit (SD) of the Configuration Register is configured 1’b. Once programmed, the device enters the shutdown mode immediately and stops any current temperature conversion. If the shutdown mode is entered during local temperature conversion, no update to local/remote temperature result occurs. If the shutdown mode is entered during remote temperature conversion, no update to the remote temperature result occurs, but the local temperature result is updated since the local temperature conversion is already completed. When the shutdown bit (SD) is configured to 0’b, the device remains in continuous conversion state. 7.4.2 One-Shot Conversion When the TMP411/TMP411D is in shutdown mode (SD = 1 in the Configuration Register), a single conversion on both channels starts by writing any value to the One-Shot Start Register (pointer address 0Fh). This write operation starts one conversion, and the TMP411/TMP411D device returns to shutdown mode when the conversion is complete. The value of the data sent in the write command is irrelevant, and is not stored by the TMP411/TMP411D. When the TMP411/TMP411D is in shutdown mode, an initial 200μs is required before a one-shot command is given. TMP411, TMP411D SBOS383E – DECEMBER 2006 – REVISED JULY 2025 www.ti.com 24 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: TMP411 TMP411D |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |