| 전자부품 데이터시트 검색엔진 |
|
LM5145 데이터시트(PDF) 33 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM5145 데이터시트(HTML) 33 Page - Texas Instruments |
|
33 / 73 page ![]() OUT OUT O L SW IN V V L 1 I F V § · ˜ ¨ ¸ ' ˜ © ¹ (11) L L(peak) OUT I I I 2 ' (12) Check the inductor data sheet to make sure that the saturation current rating is well above the peak inductor current of a particular design. Ferrite-cored inductors have very low core loss and are preferred at high switching frequencies, so design goals can then concentrate on copper loss and preventing saturation. Low inductor core loss is evidenced by reduced no-load input current and higher light-load efficiency. However, ferrite core materials exhibit a hard saturation characteristic where the inductance collapses abruptly when the saturation current is exceeded. This action results in an outsized increase in inductor ripple current and higher output voltage ripple, not to mention reduced efficiency and compromised reliability. Note that the saturation current rating of an inductor generally decreases as the core temperature increases. Of course, accurate overcurrent protection is critical to avoiding inductor saturation. 8.1.1.3 Output Capacitors Ordinarily, the energy stored by the output capacitors combined with the control loop response prescribe to maintain the integrity of the output voltage within the dynamic (transient) tolerance specifications. The usual boundaries restricting the output capacitors in power management applications are driven by finite available PCB area, component footprint and profile, and cost. As the load step amplitude and slew rate increase, the capacitor parasitics – equivalent series resistance (ESR) and equivalent series inductance (ESL) – take greater precedence in shaping the load transient response of the regulator. The output capacitor, COUT, filters the inductor ripple current and provides a reservoir of charge for step-load transient events. Typically, ceramic capacitors provide extremely low ESR to reduce the output voltage ripple and noise spikes, while tantalum and polymer electrolytic capacitors provide a large bulk capacitance in a relatively compact footprint for transient loading events. Based on the static specification of peak-to-peak output voltage ripple denoted by ΔVOUT, choose an output capacitance that is higher than that given by Equation 13. L OUT 2 2 SW OUT ESR L I C 8 F V R I ' t ˜ ' ˜ ' (13) Figure 8-1 conceptually illustrates the relevant current waveforms during both load-on and load-off transitions. As shown, the slew rate of the inductor current represent a large-signal constraint as the inductor current ramps to match the new load-current level following a load transient. This slew-rate limiting exacerbates the deficit of charge in the output capacitor, which must be replenished as rapidly as possible during and after a load-on transient. Similarly, during and after a load-off transient, the slew rate limiting of the inductor current adds to the surplus of charge in the output capacitor that must be depleted as quickly as possible. www.ti.com LM25137 SNVSCU4 – OCTOBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 33 Product Folder Links: LM25137 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |