absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†

Supply voltage (VCC+ with respect to VCC–)

15 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Analog input voltage (IN – or IN +)

VCC– to VCC+

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reference voltage range

VCC– to VCC+

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Clock input voltage range

0 V to VCC+

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating free-air temperature range, TA

0

°C to 70°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range, Tstg

–65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: N package

260

°C

. . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

recommended operating conditions

MIN

NOM

MAX

UNIT

Supply voltage, VCC+

4

5

6

V

Supply voltage, VCC–

–3

–5

–8

V

Reference voltage, Vref

1

V

High-level input voltage, CLK, RUN/HOLD, VIH

2.8

V

Low-level input voltage, CLK, RUN/HOLD, VIL

0.8

V

Differential input voltage, VID

VCC – +1

VCC+ – 0.5

V

Maximum operating frequency, fclock (see Note 1)

1.2

2

MHz

Operating free-air temperature range, TA

0

70

°C

NOTE 1: Clock frequency range extends down to 0 Hz.

electrical characteristics, VCC+ = 5 V, VCC– = 5 V, Vref = 1 V, fclock = 120 kHz, TA = 25°C (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VOH

High level output voltage

D1-D5, B1,B2,B4,B8

IO = – 1 mA

2.4

5

V

VOH

High-level output voltage

Other outputs

IO = – 10 µA

4.9

5

V

VOL

Low-level output voltage

IO = 1.6 mA

0.4

V

VON(PP) Peak-to-peak output noise voltage (see Note 2)

VID = 0,

Full scale = 2 V

15

µV

αVO

Zero-reading temperature coefficient of output voltage

VID = 0,

0

°C ≤ TA ≤ 70°C

0.5

2

µV/°C

IIH

High-level input current

VI = 5 V,

0

°C ≤ TA ≤ 70°C

0.1

10

µA

IIL

Low-level input current

VI = 0 V,

0

°C ≤ TA ≤ 70°C

– 0.02

– 0.1

mA

II

Input leakage current IN

and IN +

VID =0

TA = 25°C

1

10

pA

II

Input leakage current, IN – and IN +

VID = 0

0

°C ≤ TA ≤ 70°C

250

pA

ICC

Positive supply current

f lk =0

TA = 25°C

1

2

mA

ICC +

Positive supply current

fclock = 0

0

°C ≤ TA ≤ 70°C

3

mA

ICC

Negative supply current

f lk =0

TA = 25°C

– 0.8

–2

mA

ICC –

Negative supply current

fclock = 0

0

°C ≤ TA ≤ 70°C

–3

mA

Cpd

Power dissipation capacitance

See Note 3

40

pF

NOTES:

2. This is the peak-to-peak value that is not exceeded 95% of the time.

3. Factor-relating clock frequency to increase in supply current. At VCC+ = 5 V, ICC+ = ICC+(fclock = 0) + Cpd × 5 V × fclock

Rev. 00

HT7135A

TLC7135A