전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

RF2514PCBA-41X 데이터시트(PDF) 4 Page - RF Micro Devices

부품명 RF2514PCBA-41X
상세설명  VHF/UHF TRANSMITTER
PDF  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  RFMD [RF Micro Devices]
홈페이지  http://www.rfmd.com
Logo RFMD - RF Micro Devices

RF2514PCBA-41X 데이터시트(HTML) 4 Page - RF Micro Devices

  RF2514PCBA-41X Datasheet HTML 1Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 2Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 3Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 4Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 5Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 6Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 7Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 8Page - RF Micro Devices RF2514PCBA-41X Datasheet HTML 9Page - RF Micro Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 18 page
background image
4 of 18
RF2514
Rev A5 DS040115
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com.
Pin
Function
Description
Interface Schematic
1GND1
Ground connection for the analog circuits, including TX buffer and output
amplifier. Internally connected to die flag. For best performance, keep
traces physically short and connect immediately to ground plane.
2PD
Power Down control for all circuitry. When this pin is a logic “low” all circuits
are turned off. When this pin is a logic “high”, all circuits are operating nor-
mally. See electrical parameters for “high” and “low” thresholds.
3TXOUT
Transmitter output. This output is an open collector and requires a pull-up
inductor for bias/matching and a tapped capacitor for matching.
4VCC1
This pin is used to supply bias to the TX buffer amplifier.
5MOD IN
AM analog or digital modulation can be imparted to the carrier by an input
to this pin. An external resistor is used to bias the output amplifiers through
this pin. The voltage at this pin must not exceed 1.1V. Higher voltages may
damage the device.
See pin 3.
6VCC2
This pin is used to supply DC bias to the VCO, crystal oscillator, pre-scaler,
phase detector, and charge pump. An IF bypass capacitor should be con-
nected directly to this pin and returned to ground.
7GND2
Digital PLL ground connection.
8VREF P
Bias voltage reference pin for bypassing the prescaler and phase detector.
The bypass capacitor should be of appropriate size to provide filtering of
the reference crystal frequency and be connected directly to this pin.
9GND3
See pin 1.
10
RESNTR-
The RESNTR pins are used to supply DC voltage to the VCO, as well as to
tune the center frequency of the VCO. Equal value inductors should be con-
nected to this pin and pin 11.
11
RESNTR+
See pin 10.
12
LOOP FLT
Output of the charge pump. An RC network from this pin to ground is used
to establish the PLL bandwidth.
V CC
PD
TX OUT
MOD IN
RF IN
VR EFP
VCC
RESNTR-
RESNTR+
LOOP FLT
4 k
Ω
LOOP FLT
VCC



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com