| 전자부품 데이터시트 검색엔진 |
|
AM79C961KC/W 데이터시트(PDF) 39 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
AM79C961KC/W 데이터시트(HTML) 39 Page - Advanced Micro Devices |
|
39 / 173 page ![]() P R E L I M I N A R Y AMD 1-513 Am79C961 Plug and Play Logical Device Control Registers Activate 0x30 For each logical device there is one activate register that controls whether or not the logical device is active on the ISA bus. Bit[0], if set, activates the logical device. Bits[7:1] are reserved and must be zero. This is a read/write register. Before a logical device is activated, I/O range check must be disabled. I/O Range Check 0x31 This register is used to perform a conflict check on the I/O port range programmed for use by a logical device. Bit[7:2] Reserved Bit 1[1] Enable I/O Range check, if set then I/O Range Check is enabled. I/O range check is only valid when the logical device is inactive. Bit[0], if set, forces the logical device to respond to I/O reads of the logical device’s assigned I/O range with a 0x55 when I/O range check is in operation. If clear, the logical device drives 0xAA. This register is read/write. Name Address Port Value Definition Memory Space Configuration Memory base address 0x40 Read/write value indicating the selected memory base address bits[23:16] for bits[23:16] descriptor 0 memory descriptor 0. This is the Boot Prom Space. Memory base address 0x41 Read/write value indicating the selected memory base address bits[15:08] for bits[15:08] descriptor 0 memory descriptor 0. Memory control 0x42 Bits[2:1] specifies 8/16-bit control. The encoding is identical to memory control (bits[4:3]) of the information field in the memory descriptor. Bit[0], =0, indicates the next field is used as a range length for decode (implies range length and base alignment of memory descriptor are equal). Bit[0] is read-only. Memory upper limit 0x43 Read/write value indicating the selected memory high address bits[23:16] for address; memory descriptor 0. If bit[0] of memory control is 0, this is the range length. If bit[0] of memory control is 1, this is considered invalid. Memory upper limit 0x44 Read/write value indicating the selected memory high address bits[15:08] for memory descriptor 0, either a memory address or a range length as described above. Memory descriptor 1 0x48-0x4C Memory descriptor 1. This is the SRAM Space for Shared Memory. Name Register Index Definition bits[23:16] or range length; bits[23:16] for descriptor 0 bits[15:08] or range length; bits[15:08] for descriptor 0 I/O Space Configuration I/O port base address 0x60 Read/write value indicating the selected I/O lower limit address bits[15:08] for I/O bits[15:08] descriptor 0 descriptor 0. If a logical device indicates it only uses 10 bit encoding, then bits[15:10] do not need to be supported. I/O port base address 0x61 Read/write value indicating the selected I/O lower limit address bits[07:00] for I/O bits[07:00] descriptor 0 descriptor 0. Name Register Index Definition |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |