전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

DIO2399ASC6 데이터시트(PDF) 9 Page - DIOO MICROCIRCUITS CO., LTD

부품명 DIO2399ASC6
상세설명  Current Shunt Monitor
PDF  13 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  DIOO [DIOO MICROCIRCUITS CO., LTD]
홈페이지  https://www.dioo.com/#/
Logo DIOO - DIOO MICROCIRCUITS CO., LTD

DIO2399ASC6 데이터시트(HTML) 9 Page - DIOO MICROCIRCUITS CO., LTD

Back Button DIO2399ASC6 Datasheet HTML 5Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 6Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 7Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 8Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 9Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 10Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 11Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 12Page - DIOO MICROCIRCUITS CO., LTD DIO2399ASC6 Datasheet HTML 13Page - DIOO MICROCIRCUITS CO., LTD  
Zoom Inzoom in Zoom Outzoom out
 9 / 13 page
background image
DIO2399A/B
www.dioo.com
© 2023 DIOO MICROCIRCUITS CO., LTD
DIO2399A/B• Rev. 1.7
voltage, the REF pin should be buffered by an op amp.
In systems where the DIO2399X output can be sensed differentially, such as by a differential input
analog-to-digital converter (ADC) or by using two separate ADC inputs, the effects of external impedance on
the REF input can be canceled. Figure 10 depicts a method of taking the output from the DIO2399X by using the
REF pin as a reference.
Figure 10. Sensing DIO2399X to cancel effects of impedance on the REF input
Using the DIO2399X with common-mode transients above 26 V
With a small amount of additional circuitry, the DIO2399X series can be used in circuits subject to transients
higher than 26 V, such as automotive applications. Use only zener diode or zener-type transient absorbers
(sometimes referred to as Transzorbs); any other type of transient absorber has an unacceptable time delay.
Start by adding a pair of resistors as shown in Figure 11 as a working impedance for the zener. It is desirable
to keep these resistors as small as possible, most often around 10 Ω. Larger values can be used with an effect
on gain that is discussed in the section on input filtering. Because this circuit limits only short-term transients,
many applications are satisfied with a 10 Ω resistor along with conventional zener diodes of the lowest power
rating that can be found. This combination uses the least amount of board space.
Figure 11. DIO2399X transient protection using dual zener diodes
In the event that low-power zeners do not have sufficient transient absorption capability and a higher power
transzorb must be used, the most package-efficient solution then involves using a single transzorb and back-to-
back diodes between the device inputs. This method is shown in Figure 12.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com