Tantalums also have good temperature stability: a good

quality Tantalum will typically show a capacitance value that

varies less than 10-15% across the full temperature range of

125˚C to −40˚C. ESR will vary only about 2X going from the

high to low temperature limits.

The increasing ESR at lower temperatures can cause oscil-

lations when marginal quality capacitors are used (if the ESR

of the capacitor is near the upper limit of the stability range at

room temperature).

ALUMINUM: This capacitor type offers the most capaci-

tance for the money. The disadvantages are that they are

larger in physical size, not widely available in surface mount,

and have poor AC performance (especially at higher fre-

quencies) due to higher ESR and ESL.

Compared by size, the ESR of an aluminum electrolytic is

higher than either Tantalum or ceramic, and it also varies

greatly with temperature. A typical aluminum electrolytic can

exhibit an ESR increase of as much as 50X when going from

25˚C down to −40˚C.

It should also be noted that many aluminum electrolytics only

specify impedance at a frequency of 120 Hz, which indicates

they have poor high frequency performance. Only aluminum

electrolytics that have an impedance specified at a higher

frequency (between 20 kHz and 100 kHz) should be used for

the LP396XEP. Derating must be applied to the manufactur-

er’s ESR specification, since it is typically only valid at room

temperature.

Any applications using aluminum electrolytics should be

thoroughly tested at the lowest ambient operating tempera-

ture where ESR is maximum.

PCB LAYOUT

Good PC layout practices must be used or instability can be

induced because of ground loops and voltage drops. The

input and output capacitors must be directly connected to the

input, output, and ground pins of the LP3962EP/5EP using

traces which do not have other currents flowing in them

Kelvin connect).

The best way to do this is to lay out C

device with short traces to the V

The regulator ground pin should be connected to the exter-

nal circuit ground so that the regulator and its capacitors

have a "single point ground".

It should be noted that stability problems have been seen in

applications where "vias" to an internal ground plane were

used at the ground points of the LP3962EP/5EP IC and the

input and output capacitors. This was caused by varying

ground potentials at these nodes resulting from current flow-

ing through the ground plane. Using a single point ground

technique for the regulator and it’s capacitors fixed the prob-

lem.

Since high current flows through the traces going into V

IN

and coming from V

these pins so there is no voltage drop in series with the input

and output capacitors.

RFI/EMI SUSCEPTIBILITY

RFI (radio frequency interference) and EMI (electromagnetic

interference) can degrade any integrated circuit’s perfor-

mance because of the small dimensions of the geometries

inside the device. In applications where circuit sources are

present which generate signals with significant high fre-

ensure that this does not affect the IC regulator.

If RFI/EMI noise is present on the input side of the

LP396XEP regulator (such as applications where the input

source comes from the output of a switching regulator), good

ceramic bypass capacitors must be used at the input pin of

the LP396XEP.

If a load is connected to the LP396XEP output which

switches at high speed (such as a clock), the high-frequency

current pulses required by the load must be supplied by the

capacitors on the LP396XEP output. Since the bandwidth of

the regulator loop is less than 100 kHz, the control circuitry

cannot respond to load changes above that frequency. The

means the effective output impedance of the LP396XEP at

frequencies above 100 kHz is determined only by the output

capacitor(s).

In applications where the load is switching at high speed, the

output of the LP396XEP may need RF isolation from the

load. It is recommended that some inductance be placed

between the LP396XEP output capacitor and the load, and

good RF bypass capacitors be placed directly across the

load.

PCB layout is also critical in high noise environments, since

RFI/EMI is easily radiated directly into PC traces. Noisy

circuitry should be isolated from "clean" circuits where pos-

sible, and grounded through a separate path. At MHz fre-

quencies, ground planes begin to look inductive and RFI/

EMI can cause ground bounce across the ground plane.

In multi-layer PCB applications, care should be taken in

layout so that noisy power and ground planes do not radiate

directly into adjacent layers which carry analog power and

ground.

OUTPUT ADJUSTMENT

An adjustable output device has output voltage range of

1.215V to 5.1V. To obtain a desired output voltage, the

following equation can be used with R1 always a 10k

Ω

resistor.

For output stability, C

OUTPUT NOISE

Noise is specified in two ways-

Spot Noise or Output noise density is the RMS sum of all

noise sources, measured at the regulator output, at a spe-

cific frequency (measured with a 1Hz bandwidth). This type

of noise is usually plotted on a curve as a function of fre-

quency.

Total output Noise or Broad-band noise is the RMS sum

of spot noise over a specified bandwidth, usually several

decades of frequencies.

Attention should be paid to the units of measurement. Spot

noise is measured in units µV/

noise is measured in µV(rms).

The primary source of noise in low-dropout regulators is the

internal reference. In CMOS regulators, noise has a low

frequency component and a high frequency component,

which depend strongly on the silicon area and quiescent

current. Noise can be reduced in two ways: by increasing the

transistor area or by increasing the current drawn by the

www.national.com

11