전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

DIO6905FT6 데이터시트(PDF) 12 Page - DIOO MICROCIRCUITS CO., LTD

부품명 DIO6905FT6
상세설명  2 A, Synchronous, Step-Down Converter with Low 15 μA Quiescent Current
PDF  15 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  DIOO [DIOO MICROCIRCUITS CO., LTD]
홈페이지  https://www.dioo.com/#/
Logo DIOO - DIOO MICROCIRCUITS CO., LTD

DIO6905FT6 데이터시트(HTML) 12 Page - DIOO MICROCIRCUITS CO., LTD

Back Button DIO6905FT6 Datasheet HTML 7Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 8Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 9Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 10Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 11Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 12Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 13Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 14Page - DIOO MICROCIRCUITS CO., LTD DIO6905FT6 Datasheet HTML 15Page - DIOO MICROCIRCUITS CO., LTD  
Zoom Inzoom in Zoom Outzoom out
 12 / 15 page
background image
DIO6905
www.dioo.com
© 2023 DIOO MICROCIRCUITS CO., LTD
DIO6905 • Rev. 1.8
- 12 -
When using ceramic capacitors, the capacitance dominates the impedance at the switching frequency, and
causes most of the output voltage ripple. For simplification, the output voltage ripple can be estimated with
Equation (9):
)
V
V
-
(1
*
C
*
L
*
f
*
8
V
=
V
IN
OUT
2
1
2
S
OUT
OUT
△
(9)
For tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For
simplification, the output ripple can be approximated with Equation (10):
ESR
IN
OUT
1
S
OUT
OUT
R
*
)
V
V
(1
*
L
*
f
V
=
V
△
(10)
The characteristics of the output capacitor also affect the stability of the regulation system.
PCB Layout Recommendation
Efficient PCB layout is critical for stable operation. For the high-frequency switching converter, a poor layout
design can result in poor line or load regulation and stability issues. For best results, refer to Figure 19 and follow
the guidelines below.
(1) Place the high-current paths (GND, IN, and SW) as close to the device as possible with short, direct, and wide
traces.
(2) Keep the input capacitor as close to IN and GND as possible.
(3) Place the external feedback resistors next to FB.
(4) Keep the switching node SW short and away from the feedback network.
(5) Keep the VOUT sense line as short as possible or keep it away from the power inductor and the surrounding
inductors.
Figure 19. Two ends of input decoupling capacitor close to pin 2 and pin 3



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com