전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

Preview PDF HTML

LDDEVALP 데이터시트(PDF) 13 Page - Wavelength Electronics, Inc.

부품명 LDDEVALP
상세설명  Low Noise Laser Diode Drivers
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  WAVELENGTH [Wavelength Electronics, Inc.]
홈페이지  https://www.teamwavelength.com/
Logo WAVELENGTH - Wavelength Electronics, Inc.

LDDEVALP 데이터시트(HTML) 13 Page - Wavelength Electronics, Inc.

Back Button LDDEVALP Datasheet HTML 9Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 10Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 11Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 12Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 13Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 14Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 15Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 16Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 17Page - Wavelength Electronics, Inc. Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 28 page
background image
© 2025
www.teamWavelength.com
13
LDD P SERIES LASER DIODE DRIVER
adjusT LaseR diode cuRRenT Via moduLaTion (oPTionaL)
There are two ways to utilize the Modulation Input to adjust
the laser diode current remotely:
•
Connect an external trimpot or potentiometer to pin 3.
See upper half of
Figure 15.
•
Connect a signal generator to pin 3. See lower half of
Figure 15.
External
Trimpot
V+ (pin 8)
Bandgap
Voltage
Reference
CURRENT
FEEDBACK
CURRENT
MONITOR
MODULATION
GND
1
2
3
4
CURRENT
FEEDBACK
CURRENT
MONITOR
MODULATION
GND
1
2
3
4
Signal
Generator
Ground
+
-
Figure 15. Two separate ways to control the laser diode
current remotely.
Upper: External Trimpot connected to pin 3.
Lower: Signal Generator connected to pin 3.
The modulation input adjusts the laser diode current by
reducing the laser diode current from the setting determined
by the Output Current Adjust trimpot proportional to the
voltage applied to pin 3.
The modulation current (I
MOD) is given by Equation 4.
Equation 4. I
MOD = IOP + VPIN3 (TFMOD )
where TF
MOD is the laser diode transfer function found in
Table 3. Recall that TF
MOD is negative.
CAUTION: The modulation input voltage must always be
maintained within the power supply voltage range between
pin 8 and pin 4. A voltage on the modulation input below
ground may produce excessive laser diode currents.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com