G-215

D4NH

Changing the Head Direction

By removing the four screws of the head, the mounting direction of

the head can be changed. The head can be mounted in four direc-

tions. Be sure that no foreign material will enter the head during a

change in direction.

Arm Lever Mounting Position

The arm lever is mounted upwards in the center position before ship-

ping. To change the position, loosen the arm lever mounting screw,

dismount the arm lever, and mount the arm lever in the left or right

position.

Wiring

• When connecting to the terminals via insulating tube and M3.5

crimp terminals, arrange the crimp terminals as shown below so

that they do not rise up onto the case or the cover. Applicable lead

wire size: AWG20 to AWG18 (0.5 to 0.75 mm2).

Use lead wires of an appropriate length, as shown below. Not doing

so may result in excess length causing the cover to rise and not fit

properly.

One-conduit Type (3 Poles)

Two-conduit Type (3 Poles)

• Do not push crimp terminals into gaps in the case interior. Doing so

may cause damage or deformation of the case.

• Use crimp terminals not more than 0.5 mm in thickness. Otherwise,

they will interfere with other components inside the case. The crimp

terminals shown below are not more than 0.5 mm thick.

J.S.T is a Japanese manufacturer.

Contact Arrangement

• The following diagrams show the contact arrangements used for

screw terminal types and connector types.

Screw Terminal Type

Connector Type

• Applicable socket: XS2F (OMRON).

• Refer to the G010 Connector Catalog for details on socket pin num-

bers and lead wire colors.

Socket Tightening (Connector Type)

• Turn the socket connector screws by hand and tighten until no

space remains between the socket and the plug.

• Make sure that the socket connector is tightened securely. Other-

wise, the rated degree of protection (IP67) may not be maintained

and vibration may loosen the socket connector.

Conduit Opening

• Connect a recommended connector to the opening of the conduit

and tighten the connector to the specified torque. The case may be

damaged if an excessive tightening torque is applied.

• When using 1/2-14NPT, wind sealing tape around the joint between

the connector and conduit opening so that the enclosure will con-

form to IP67.

• Use a cable with a suitable diameter for the connector.

• Attach and tighten a conduit cap to the unused conduit opening

when wiring. Tighten the conduit cap to the specified torque. The

conduit cap is provided with the Switch (2-conduit types).

Manufacture

Type

Wire size

J.S.T.

FV0.5-3.7 (F type)

V0.5-3.7 (straight type)

AWG20 (0.5 mm2)

1 to 3

4.5 to 5 dia.

8 to 10 dia.

1 to 3

22

21

34

33

12

11

A

A

C

E

B

D

F

C

E

B

D

F

28 mm

Tolerance

±2 mm

33 mm

42 mm

22

21

34

33

12

11

A

C

E

B

D

F

A

C

E

BD F

28 mm

Tolerance

±2 mm

Left hand

42 mm

A

C

E

BD F

28 mm

Tolerance

±2 mm

Right hand

42 mm

L

l

F

B

D dia.

dz dia.

Crimp terminal

Terminal screw

t:

0.5 mm

dz dia.:

3.7 mm

D dia.:

2.9 mm

B:

6.6 mm

L:

19 mm

F:

7.7 mm

I :

8.0 mm

Correct

Incorrect

D4NH-

@D@@ (3NC)

11

21

12

22

31

32

D4NH-

@B@@ (2NC)

11

31

12

32

D4NH-

@C@@ (2NC/1NO)

D4NH-

@F@@ (2NC/1NO (MBB))

D4NH-

@A@@ (1NC/1NO)

D4NH-

@E@@ (1NC/1NO (MBB))

33

34

11

21

12

22

11

33

12

34

1

3

24

D4NH-9B

@@ (2NC)

(1) 11

(3) 31

12 (2)

32 (4)

D4NH-9A

@@ (1NC/1NO)

D4NH-9E

@@ (1NC/1NO (MBB))

(1) 11

(3) 33

Pin No. (Terminal No.)

12 (2)

34 (4)