3

E3X-HD

Ratings and Specifications

*1. The E3X-ECT EtherCAT Sensor Communications Unit and the E3X-CRT CompoNet Sensor Communications Unit can be used.

*2. Use either the E3X-CN11 (master connector, 3 conductors) or the E3X-CN12 (slave connector, 1 conductor).

*3. The communications function and mutual interference prevention function are disabled when the detection mode is set to Super-high-speed mode (SHS).

When including E3X-DA-S with activated power tuning, mutual interference prevention is possible for up to 6 units.

When including E3X-MDA with activated power tuning, mutual interference prevention is possible for up to 5 units.

Item

Type

Standard

Model for Sensor Communications Unit *1

NPN

output

E3X-HD11

E3X-HD6

E3X-HD14

E3X-HD0

PNP

output

E3X-HD41

E3X-HD8

E3X-HD44

Connecting

method

Pre-wired

Wire-saving

Connector *2

M8 Connector

Connector for Sensor

Communications Unit

Light source (wavelength)

Red, 4-element LED (625 nm)

Power supply voltage

12 to 24 VDC

±10%, ripple (P-P) 10% max.

Supplied from the connector through

the Sensor Communications Unit

Power

consump

tion

Normal mode

720 mW max. (Current consumption: 30 mA max. at 24 VDC, 60 mA max. at 12 VDC)

Eco ON

530 mW max. (Current consumption: 22 mA max. at 24 VDC, 44 mA max. at 12 VDC)

Eco LO

640 mW max. (Current consumption: 26 mA max. at 24 VDC, 53 mA max.

at 12 VDC)

−

Control output

Load power supply voltage: 26.4 VDC max., open-collector output

Load current: Groups of 1 to 3 Amplifier Units: 100mA max.,

Groups of 4 to 16 Amplifier Units: 20mA max.

Residual voltage: At load current of less than 10 mA: 1 V max.,

At load current of 10 to 100 mA: 2 V max.

OFF current: 0.1 mA max.

−

Protection circuits

Power supply reverse polarity protection, output short-circuit

protection and output reverse polarity protection

Power supply reverse polarity

protection and output short-circuit

protection

Response

time

Super-high-speed

mode (SHS) *3

NPN outputs: Operate or reset: 50

μs

PNP outputs: Operate or reset: 55

μs

−

High-speed mode (HS) Operate or reset: 250

μs (default setting)

Standard mode (Stnd)

Operate or reset: 1 ms

Giga-power mode (GIGA) Operate or reset: 16 ms

Maximum connectable Units

16 units

with E3X-CRT: 16 units

with E3X-ECT: 30 units

Mutual interference prevention

Possible for up to 10 units (optical communications sync) *3

Auto power control (APC)

Always ON

Other functions

Power tuning, differential detection, DPC, timer (OFF-delay, ON-delay, or one-shot),

zero reset, resetting settings, and Eco mode

Ambient illumination

(Receiver side)

Incandescent lamp: 20,000 lx max., Sunlight: 30,000 lx max.

Ambient temperature range

Operating:

Groups of 1 to 2 Amplifiers:

−25 to 55°C,

Groups of 3 to 10 Amplifiers:

−25 to 50°C,

Groups of 11 to 16 Amplifiers:

−25 to 45°C

Storage:

−30 to 70°C

(with no icing or condensation)

Operating:

Groups of 1 to 2 Amplifiers: 0 to 55

°C,

Groups of 3 to 10 Amplifiers: 0 to 50

°C,

Groups of 11 to 16 Amplifiers: 0 to 45

°C,

Groups of 17 to 30 Amplifiers: 0 to 40

°C

Storage:

−30 to 70°C

(with no icing or condensation)

Ambient humidity range

Operating and storage: 35% to 85% (with no condensation)

Insulation resistance

20 M

Ω min. (at 500 VDC)

Dielectric strength

1,000 VAC at 50/60 Hz for 1 minute

Vibration resistance

(destruction)

10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X,

Y, and Z directions

10 to 150 Hz with a 0.7-mm double

amplitude for 80 minutes each in X, Y,

and Z directions

Shock resistance (destruction)

500 m/s2 for 3 times each in X, Y, and Z directions

150 m/s2 for 3 times each in X, Y, and

Z directions

Degree of protection

IEC 60529 IP50 (with Protective Cover attached)

−

Weight (packed state/unit only)

Approx. 105 g/

Approx. 65 g

Approx. 60 g/

Approx. 20 g

Approx. 70 g/

Approx. 25 g

Approx. 65 g/Approx. 25 g

Materials

Case

Polycarbonate (PC)

Heat-resistant ABS (connector: PBT)

Cover

Polycarbonate (PC)

Cable

PVC

−

Accessories

Instruction Manual