| 전자부품 데이터시트 검색엔진 |
|
NPM1100-CAAA-R 데이터시트(PDF) 16 Page - Nordic Semiconductor |
|
|
|||||||||||||||||||||||||||||
NPM1100-CAAA-R 데이터시트(HTML) 16 Page - Nordic Semiconductor |
|
16 / 58 page ![]() Core components Limit set method Pin configuration VBUS current limit Fixed 100 mA ISET = D- = AVSS D+ = NC 100 mA Fixed 500 mA ISET = VSYS D- = AVSS D+ = NC 500 mA USB port detection ISET = AVSS D+ and D- are connected to host 100 mA if SDP detected 500 mA if DCP/CDP detected USB port detection and negotiation (requires a USB enabled microcontroller) ISET = microcontroller GPIO D+ and D- connected to USB host 100 mA if SDP detected, ISET = LOW 500 mA if SDP detected, ISET = HIGH 500 mA if DCP/CDP Table 8: Pin configuration for VBUS current limit When a microcontroller is controlling ISET with GPIO for USB port negotiation, ISET must be set LOW on reset and whenever USB is disconnected. ISET is only set HIGH when the USB port is SDP and negotiation for a higher current limit is complete. See the circuit schematics in the Reference circuitry on page 44 for designs illustrating these configurations. 6.1.2 SYSREG resistance and output voltage SYSREG regulates the VINT voltage to VSYSREG. When the VBUS pin voltage is below VSYSREG, there is typically RONREG resistance between VBUS and VINT. 6.1.3 VBUS overvoltage and undervoltage protection The overvoltage threshold for VBUS is VBUSOVP. The undervoltage threshold for VBUS is VBUSMIN. SYSREG is disabled when VBUS voltage is above the overvoltage threshold VBUSOVP, or below the undervoltage threshold VBUSMIN. This isolates VBUS and prevents current flowing from VINT to VBUS. 6.1.4 VBUS disconnect SYSREG isolates VBUS from VINT when VBUS is disconnected and the voltage drops below VBUSMIN. When VBUS reaches VBUSULP, the device enters an ultra-low power (ULP) operation mode. This takes TDISCONN, dependent on capacitive load on VBUS. The device stays in a ULP mode while VBUS is under VBUSULP. 6.1.5 Electrical parameters Symbol Description Min. Typ. Max. Units IBUSLIM1 Max VBUS input current, CDP/DCP USB or ISET = HIGH 450 - 500 mA 4445_367 v1.0 16 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |