| 전자부품 데이터시트 검색엔진 |
|
331035 데이터시트(PDF) 2 Page - Stannol GmbH & Co KG |
|
|
|||||||||||||||||||||||||||||
331035 데이터시트(HTML) 2 Page - Stannol GmbH & Co KG |
|
2 / 2 page ![]() The above values are typical and represent no form of specification. The Data Sheet serves for information purposes. Any verbal or written advise is not binding for the company, whether such information originates from the company offices or from a sales representative. This is also in respect of any protection rights of third parties, and does not release the customer from the responsibility of verifying the products of the company for suitability of use for the intended process or purpose. Should any liability on the part of the company arise, the company will only indemnify for loss or damage to the same extent as for defects in quality. TDB_ME_ECOLOY_TC_EN Page 2 of 2 Issue: 01.04.09 STANNOL GmbH Oskarstraße 3-7 • 42283 Wuppertal • Tel. +49 (0)202-585-0 • Telefax +49 (0)202-585111 • E-Mail info@stannol.de • Web www.stannol.de Wenn’s ums Löten geht When it’s about soldering Quand il s’agit du soudage Recommended Conditions of Use Wave soldering The use of ECOLOY ® TC Solder requires a soldering temperature of about 260 to 280°C. Optimum conditions must be found out depending on the type of PCB. The application of additional Inertgas is very helpful. The absence of Oxygen and oxides on the solder surface will enhance the wetting of the solder and when leaving the solder wave no excessive solder will remain on the solder joint. Inertgas will reduce the formation of bridges and icicles. The formation of dross will be reduced enormously. Fluxes for wave soldering In principle all common fluxes like STANNOL ® EF350 are suitable for lead-free soldering. The solid content should not be as low as for tin-lead, because due to the high thermal demand of the PCB there is more preheat and higher solder bath temperature necessary. Therefore stability and sustainable activity is of importance. As a complete ecological solution the use of VOC-free liquid fluxes should be an option, e.g. STANNOL ® WF300S. Because the solvent is water, all process requirements have to be adapted to the specific properties of the flux. Rework and Repair All temperature profiles used for tin-lead have to be changed to new requirements of the lead-free alloys (melting point +44°C). If components are still with tin-lead coating, solder joint properties will become less reliable than completely lead free. Supply forms Solder Wire (solid and flux cored) Triangular bars Kg-bars Ingots with hanging hole Health and Safety Before using please read the material safety data sheet carefully and observe the safety precautions described. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |