| 전자부품 데이터시트 검색엔진 |
|
DLP-232PC 데이터시트(PDF) 4 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
DLP-232PC 데이터시트(HTML) 4 Page - THAT Corporation All rights reserved. |
|
4 / 14 page ![]() THAT 5171-DEMO Datasheet Page 4 of 14 Document 600189 Rev 01 THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Copyright © 2018, THAT Corporation; All rights reserved. Connections: Power The USB interface runs on USB bus power, but the rest of the demo board requires an external power supply. +/-15 V (maximum +/-17V) supplies the analog circuitry. +48V phantom power is input (not generated on the board) and switched on and off via the on-board Phantom Power switch. Note that the ground return for +48V phantom power is via the CHAS (chassis ground) connector. The +5V input is regulated on board to 3.3V and supplies the digital logic. Audio Input The Neutrik combo connector accepts an XLR or ¼” TRS cable. Maximum input signal level is +22dBu with ±15 V supplies. The 1/4” TRS signal path includes a 20 dB pad in order to support very high line levels. Audio Output Separate XLR and ¼” TRS connectors are wired in parallel. Maximum output signal level is +22 dBu with ±15 V supplies. The differential attenuator/output buffer (U3) adds a small amount of noise and distortion to the signal and it is therefore recommended that test points TP1-TP3 be used to measure performance of the 1580/5171 ICs. USB A PC must be plugged into the demo board via USB in order to control the various parameters in the 5171. General Purpose Outputs (GPO) The GPO3:0 pins are connected to header J12. J12 is conveniently located near the prototyping area, so the user can easily connect optional circuitry to them. Note that the GPO pins are also connected to LEDs, D1-D4, and pull up and pull down resistors which set the 5171 device address during reset. Consideration must be given to how any application circuitry that is added interacts with these other functions. A note about the phantom power fault protec- tion circuitry included on the demo board: Phantom power faults are a serious concern in any preamplifier design and external protection circuitry is always required for safe and reliable operation. A momentary short at the input connector while using phantom power can cause 48 V negative spikes to appear at the preamplifier inputs, often destroying the IC if left unprotected. THAT Corporation has recently revised its protection recommendations which now include: 1) Schottky diodes 2) Larger power supply bypass capacitors. The full details of our latest recommendations can be found in our Design Brief 201, “Revisiting Phantom Power Fault Protection”, available on our website here: www.thatcorp.com/Design_Briefs.shtml The part number for our recommended Schottky diode can be found in the bill of materials included in this document. Jumper Options T-Bias Jumper, J4 The input circuit provides a jumper (J4) which enables/disables the “T-Bias” function. With a shunt installed on J4, T-Bias is disabled and the circuit provides a 1 kΩ common-mode input impedance per input leg to the XLR input. With the shunt removed from J4, T-Bias is enabled and provides a higher common mode impedance(nominally 5.1 kΩ per input leg), which will improve CMRR performance, particularly at low frequencies where mismatches in the input coupling capacitors tend to degrade it. The differential input impedance is 2 kΩ in both cases. VCM Input Jumper, J6 The output attenuator (U3) is normally biased at 0 VDC via R30 connected to ground through a shunt on jumper J6. If the J6 shunt is removed, a bias voltage may be input via J6, e.g. the common mode voltage output pin (VCOM) of an A/D Converter. External SPI Host Jumpers & Connectors The demo board has two connectors, J8 and Jl0, for connecting up to 8 boards to an external SPI master device, such as a microcontroller. J8 is not installed at the factory and it is up to the user to add it if required. Note also that current limiting resistors R34, R36, R40, and R41 must be installed with the appropriate value for the application. Please contact THAT Corporation technical support for assistance. Connections |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |