| 전자부품 데이터시트 검색엔진 |
|
6266 데이터시트(PDF) 8 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
6266 데이터시트(HTML) 8 Page - THAT Corporation All rights reserved. |
|
8 / 20 page ![]() Document 600190 Rev 05 Page 8 of 20 THAT 626x 2-Channel Low-Noise Programmable Gain Preamplifier – ADC Driver IC THAT Corporation; 45 Sumner Street; Milford, Massachusetts 01757-1656; USA Tel: +1 (508) 478-9200; Fax +1 (508) 478-0990; Web: www.thatcorp.com Copyright © 2018, THAT Corporation; All rights reserved. The THAT 626x (x=1, 3 or 6) is a family of two- channel digitally controlled microphone preamplifi- ers with integrated ADC drivers. Depending on the model, gain of the parts is programmable in 1, 3, or 6dB steps. Part 6261 6263 6266 Step size 1 dB 3 dB 6 dB The 626x family is implemented in a mixed- voltage multi-well Bi-CMOS process that integrates 10V, 5V, and 3.3V circuitry onto a single silicon die. The combination of process and design also al- lows operating the device with ±5V, 5V, and 3.3V supplies, but it may also be powered from 10V, 5V, and 3.3V supplies. THAT 626x seamlessly bridges between a pro- fessional-audio line/microphone input and a 5V- powered A/D converter. It contains two independently controlled differential analog signal processing chan- nels. The high level of integration minimizes the PCB area required for such systems. Further, THAT 626x’s low power consumption simplifies system heat management; this is especially helpful when integrating many channels in a single system. Each differential analog channel in the 626x consists of a low-voltage-noise, gain-programmable preamplifier stage, a gain-programmable ADC driver stage and a zero-crossing detector (ZCD). To mini- mize audible switching noise, gain switching events can be synchronized to moments when the ADC driv- er differential output signal is close to zero. An exter- nal signal (at the BSY pins) indicates when zero- crossing-based gain changes or GPO updates take place. Each channel can also be put into a minimum power stand-by mode when not in use. And, each channel can be muted. The part is programmed via a 4-wire serial peripheral interface (SPI) shared by the two channels. Programmable Gain Settings The 626x implements its overall gain in two stages: a preamp stage and an ADC driver stage. The preamp stage gain ranges from 0 dB to +39 dB. It can accommodate input signals as high as +16.5 dBu at the lowest gain. The ADC driver attenuates the preamp’s output by from –5 to –8dB in order to fit the signal within the typical 2 Vrms full-scale input voltage of integrated ADCs. The ADC driver also re- jects common-mode signals, providing a dc pedestal (derived from the VCM input) on which to queue the differential outputs. Gain-Programmable Preamplifier Stage The preamp stage consists of a low-voltage-noise current-feedback differential amplifier with gain pro- grammed by an array of resistors and CMOS switch- es that makes up RG. See Figure 12 for detail of one of the two channels. The RG resistor/switch array is programmed via the SPI digital control interface. The resulting gain varies from 0dB to 39dB in 3dB steps (in the 6261 and 6263) or 6dB steps (6266). The preamp feedback resistors have a nominal value of 2k. The RG values with the corresponding gains for THAT 6261, 6263 and 6266 are listed in Table 2. The RG network should be ac-coupled using an external capacitor CG. This limits dc gain to unity for all ac gain settings, ensuring that the preamp’s out- put offset voltage will be constant for all gain settings. The preamp’s differential output (between the PO+ and PO- pins) has a fixed dc common-mode level of one VBE (~0.6V) below the voltage at the input pins (IN+ and IN-). The PO+ and PO- pins are typi- cally ac-coupled to the ADC driver stage through ex- ternal capacitors (CC1 and CC2). This allows the ADC driver stage to operate around the voltage (typically +2.5V) supplied at the VCM pin. This voltage should match that required for the ADC being driven. Theory of Operation Figure 12. Analog Section Functional Block Diagram 2k Zero-Crossing Detector VAD VA+ IN- PO- DI- PO+ DI+ + + + VCM RFB+ CFB+ OUT+ OUT- CFB- RFB- CG2 C G C C1 C C2 CG1 RG IN+ VA- VA+ VA- RFB 2k 2k 2k RFB Preamplifier ADC Driver |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |