| 전자부품 데이터시트 검색엔진 |
|
M38K09RFS 데이터시트(PDF) 217 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M38K09RFS 데이터시트(HTML) 217 Page - Renesas Technology Corp |
|
217 / 328 page ![]() 2.10 Frequency synthesizer (PLL) Rev.2.00 Oct 05, 2006 page 88 of 111 38K0 Group REJ09B0337-0200 APPLICATION q X: This bit is not used here. Set it to “0” or “1” arbitrarily. •Select main clock f(XIN) as a USB clock •PLL operation mode (bit6,5): Multiplied by 8 •USB division mode (bit4,3): Divided by 6 •Enable PLL operation (bit7) •Select fSYN (8MHZ) as a system clock •Select PLL circuit output clock fVCO as a USB clock •Wait for oscillation stabilization When multiplying oscillation by PLL, wait for oscillation stabilization. CPUM (address: 3B16) ← 11101X002 USBCON (address: 1016) ← X0XXXXXX2 PLLCON (address: 0FF816) ← 111010002 Wait (approximately 1 ms) USBCON (address: 1016) ← X1XXXXXX2 Same setting procedure when hardware reset PLLCON (address: 0FF816) bit6,5 ← 002 •PLL operation mode (bit6,5): Not multiplied (Change PLL circuit output clock fVCO to f(XIN)) After recovery from stop mode Note: The above setting example assumes the operation when the external oscillating clock is 6 MHZ and the internal system clock is fSYN. Fig. 2.10.8 Related registers setting when recovery from stop mode 2.10.4 Notes on PLL q6 MHZ or 12 MHZ external oscillator can be connected as an input reference clock (f(XIN)). When using the frequency synthesized clock function, we recommend using the fastest frequency possible of f(XIN) as an input clock reference for the PLL. qWhen enabling PLL operation from PLL disabled status (disabled when reset), set the USB clock select bit of USBCON to “0” (f(XIN)) to operate with the main clock (f(XIN)). qWhen supplying fVCO to the USB block after setting PLL operation enable bit to “1” (PLL enabled), wait for the oscillation stable time (1 ms or less) of PLL to avoid any instability caused by the clock, then set USB clock select bit to “1” (USB clock). qWhen selecting fSYN as an internal system clock, fUSB must be 48 MHz. qWhen selecting fSYN as an internal system clock, change the system clock selection bit to main clock (f(XIN)) before executing STP instruction. It is because the following are needed for the low-power consumption: •fUSB must be stopped by disabling PLL operation in Stop mode. •The taimer 1 for waiting oscillation stabilization when returning from Stop mode will require the input count source. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |