TDA9109 datasheet(17/30 Pages) STMICROELECTRONICS

17 / 30 page

I.6 - Sync Identification Status

The MCU can read (address read mode : 8D) the

status register via the I

2C bus, and then select the

sync priority depending on this status.

Among other data this register indicates the pres-

ence of sync pulses on H/HVIN, VSYNCIN and

(when 12V is supplied) whether a Vext has been

extracted from H/HVIN. Both horizontal and vertical

sync are detected even if only 5V is supplied.

In order to choose the right sync priority the MCU

may proceed as follows (see I

2C Address Table) :

- refresh the status register,

- wait at least for 20ms (Max. vertical period),

- read this status register.

Sync priority choice should be :

Vext

det

H/V

det

Sync priority

Subaddress

03 (D8)

Comment

Sync type

Yes Yes

Separated H & V

Yes

Composite TTL H&V

Of course, when the choice is made, we can refresh

the sync detections and verify that the extracted

Vsync is present and that no sync type change has

occured. The sync processor also gives sync po-

larity information.

I.7 - IC status

The IC can inform the MCU about the 1st horizontal

PLL and vertical section status (locked or not) and

about the XRAY protection (activated or not).

Resetting the XRAY internal latch can be done

either by decreasing the VCC or VDD supply or

directly resetting it via the I

2C interface.

I.8 - Sync Inputs

Both H/HVIN and VSYNCIN inputs are TTL com-

patible triggers with hysterisis to avoid erratic

detection. Both inputs include a pull up resistor

connected to VDD.

I.9 - Sync Processor Output

The sync processor indicates on the HLOCKOUT

Pin whether 1st PLL is locked to an incoming

horizontal sync. HLOCKOUT is a TTL compatible

CMOS output. Its level goes to high when locked.

In the same time the D8 bit of the status register is

set to 0.

This information is mainly used to trigger safety

procedures (like reducing B+ value) as soon as a

OPERATING DESCRIPTION (continued)

Figure 5

TRAMEXT

Figure 6

change is detected on the incoming sync. Further

to this, it may be used in an automatic procedure

for free running frequency (f0) adjustment :

Sending the desired f0 on the sync input and

progressively decreasing the free running fre-

quency I

2C register value (address 02), the

HLOCKOUT Pin will go high as soon as the proper

setting is reached.

Setting the free running frequency this way allows

to fully exploit the TDA9109/S horizontal frequency

range.

II - HORIZONTAL PART

II.1 - Internal Input Conditions

A digital signal (horizontal sync pulse or TTL

composite) is sent by the sync processor to the

horizontal input. It may be positive or negative

(see Figure 5).

Using internal integration, both signals are recog-

nized if Z/T < 25%. Synchronization occurs on the

leading edge of the internal sync signal. The mini-

mum value of Z is 0.7

µs.

Another integration is able to extract the vertical

pulse from composite sync if the duty cycle is higher

than 25% (typically d = 35%) (see Figure 6).

The last feature performed is the removal of equali-

zation pulses to avoid parasitic pulses on the phase

comparator (which would be disturbed by missing

or extraneous pulses).

TDA9109/S

17/30

TDA9109 데이터시트(PDF) 17 Page - STMicroelectronics

TDA9109 데이터시트(HTML) 17 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

데이터시트 다운로드

링크 URL