전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

AT91SAM9261 데이터시트(PDF) 12 Page - ATMEL Corporation

부품명 AT91SAM9261
상세설명  AT91 ARM Thumb-based Microcontrollers
PDF  43 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  ATMEL [ATMEL Corporation]
홈페이지  http://www.atmel.com
Logo ATMEL - ATMEL Corporation

AT91SAM9261 데이터시트(HTML) 12 Page - ATMEL Corporation

Back Button AT91SAM9261 Datasheet HTML 8Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 9Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 10Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 11Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 12Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 13Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 14Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 15Page - ATMEL Corporation AT91SAM9261 Datasheet HTML 16Page - ATMEL Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 12 / 43 page
background image
12
6062KS–ATARM–15-Jan-09
AT91SAM9261 Preliminary
6.2
Test Pin
The TST pin is used for manufacturing test purposes when asserted high. It integrates a perma-
nent pull-down resistor of about 15 k
Ω to GNDBU, so that it can be left unconnected for normal
operations. Driving this line at a high level leads to unpredictable results.
6.3
Reset Pin
NRST is an open-drain output integrating a non-programmable pull-up resistor. It can be driven
with voltage at up to VDDIOP. As the product integrates power-on reset cells, the NRST pin can
be left unconnected in case no reset from the system needs to be applied to the product.
The NRST pin integrates a permanent pull-up resistor of 100 k
Ω minimum to VDDIOP.
The NRST signal is inserted in the Boundary Scan.
6.4
PIO Controller A, B and C Lines
All the I/O lines PA0 to PA31, PB0 to PB31, and PC0 to PC31 integrate a programmable pull-up
resistor of 100 k
Ω. Programming of this pull-up resistor is performed independently for each I/O
line through the PIO Controllers.
After reset, all the I/O lines default as inputs with pull-up resistors enabled, except those which
are multiplexed with the External Bus Interface signals that require to be enabled as Peripherals
at reset. This is explicitly indicated in the column “Reset State” of the PIO Controller multiplexing
tables.
6.5
Shutdown Logic Pins
The SHDN pin is an output only, driven by Shutdown Controller.
The pin WKUP is an input only. It can accept voltages only between 0V and VDDBU.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com