| 전자부품 데이터시트 검색엔진 |
|
LR8 데이터시트(PDF) 8 Page - Supertex, Inc |
|
|
|||||||||||||||||||||||||||||
LR8 데이터시트(HTML) 8 Page - Supertex, Inc |
|
8 / 11 page ![]() 8 LR8 LR8 Application Note AN-H40 Operation Except for it’s higher voltage rating, the LR8 operates like any other 3-terminal adjustable linear regulator. A simple resistive divider sets the output voltage while a capacitor at the output improves transient response and ensures regulator stability. When applicable, an input capacitor is required to provide energy storage for rectified AC. Keeping in mind that the LR8 requires at least a 10V difference between input and output for proper operation, the minimum value for CIN is: Introduction The LR8 is a high voltage 3-terminal adjustable linear regulator. Intended for operation directly off rectified AC mains, the LR8 operates at input voltages up to 450 volts, making it compatible with line voltages up to 240 VAC. It’s output voltage adjustability assures that it can be used in most any application. The LR8 is ideally suited for low power off-line DC power supplies and SMPS start-up circuits. Available in a leaded TO-92 package and a surface mount SOT-89 and D-PAK package, it is ideal for applications where space is at a premium. Relevant specifications are shown in the table below. Input Voltage Range (VOUT +10V) to 450V Output Voltage Range 1.2V to (VIN - 10V) Output Voltage Accuracy ±5% Power Dissipation TO-92: 0.74W TO-243AA (SOT-89): 1.6W TO-252 (D-PAK): 2.5W Output Current 0.5 to 10mA Load Regulation 3% Line Regulation 0.01%/V Supply Rejection 60dB typ @120Hz LR8 Specifications CI t VV IN LOAD IN pk OUT > −− () 10V where I LOAD = Load current t= Time between peaks of input waveform V IN(pk) = Peak input voltage V OUT = Output voltage Note that the LR8 requires a minimum of 0.5mA load current for proper operation. The current through the resistive divider may be included as part of the minimum load. High Voltage Linear Regulators and Constant Current Sources Using LR8 by Scott Lynch, Senior Applications Engineer LR8 Block Diagram and Typical Application Overtemp & Overcurrent 10µA 1.2V VIN VOUT ADJ LR8 Pass Element R1 R2 COUT ≥ 1µF CIN Needed for protection should VOUT exceed VIN Load Supply V R R R OUT =+ +µ 12 1 10 2 1 2 .• vA |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |