| 전자부품 데이터시트 검색엔진 |
|
LT3437IDD 데이터시트(PDF) 24 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT3437IDD 데이터시트(HTML) 24 Page - Linear Technology |
|
24 / 28 page ![]() 24 LT3437 3437fc APPLICATIO S I FOR ATIO Figure 10. Model for Loop Response – + CURRENT MODE POWER STAGE gm = 1 gm = 650µ 1.25V VC LT3437 ERROR AMP 1.6M RC R1 FB SW ESR OUTPUT R2 COUT 3437 F13 CFB CF CC Figure 11. Overall Loop Response FREQUENCY (Hz) –180 –160 –140 –120 –100 –80 –60 –40 –20 0 –40 0 60 40 20 –20 80 100 100 1k 10k 100k 3437 F12 1M 10 VOUT = 3.3V COUT = 100µF, 0.1Ω CF = 330pF RC = 25k CC = 1500pF ILOAD = 250mA A zero can be added into the loop by placing a resistor (RC) at the VC pin in series with the compensation capacitor, CC, or by placing a capacitor (CFB) between the output and the FB pin. When using RC, the maximum value has two limitations. First, the combination of output capacitor ESR and RC may stop the loop rolling off altogether. Second, if the loop gain is not rolled off sufficiently at the switching frequency, output ripple will perturb the VC pin enough to cause unstable duty cycle switching, similar to subharmonic oscillations. If needed, an additional capacitor (CF) can be added across the RC/CC network from the VC pin to ground to further suppress VC ripple voltage. With a tantalum output capacitor, the LT3437 already includes a resistor (RC) and filter capacitor (CF) at the VC pin (see Figures 10 and 11) to compensate the loop over the entire VIN range (to allow for stable pulse skipping for high VIN-to-VOUT ratios ≥ 10). A ceramic output capacitor can still be used with a simple adjustment to the resistor RC for stable operation (see Ceramic Capacitors section for stabilizing LT3430). If additional phase margin is required, a capacitor (CFB) can be inserted between the output and FB pin, but care must be taken for high output voltage applications. Sudden shorts to the output can create unacceptably large negative transients on the FB pin. For VIN-to-VOUT ratios < 10, higher loop bandwidths are possible by readjusting the frequency compensation com- ponents at the VC pin. When checking loop stability, the circuit should be oper- ated over the application’s full voltage, current and tem- perature range. Proper loop compensation may be obtained by empirical methods, as described in Application Notes 19 and 76. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |