| 전자부품 데이터시트 검색엔진 |
|
A14100A-RQ208C 데이터시트(PDF) 14 Page - Actel Corporation |
|
|
|||||||||||||||||||||||||||||
A14100A-RQ208C 데이터시트(HTML) 14 Page - Actel Corporation |
|
14 / 68 page ![]() 1-188 5V Operating Conditions Absolute Maximum Ratings 1 Free air temperature range Recommended Operating Conditions Electrical Specifications Symbol Parameter Limits Units VCC DC Supply Voltage –0.5 to +7.0 V VI Input Voltage –0.5 to VCC +0.5 V VO Output Voltage –0.5 to VCC +0.5 V IIO I/O Source Sink Current2 ±20 mA TSTG Storage Temperature –65 to +150 °C Notes: 1. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Device should not be operated outside the Recommended Operating Conditions. 2. Device inputs are normally high impedance and draw extremely low current. However, when input voltage is greater than VCC + 0.5 V or less than GND – 0.5 V, the internal protection diodes will forward bias and can draw excessive current. Parameter Commercial Industrial Military Units Temperature Range1 0 to +70 –40 to +85 –55 to +125 °C 5V Power Supply Tolerance ±5 ±10 ±10 %VCC Note: 1. Ambient temperature (TA) is used for commercial and industrial; case temperature (TC) is used for military. Symbol Parameter Test Condition Commercial Industrial Military Units Min. Max. Min. Max. Min. Max. VOH 1,2 HIGH Level Output IOH = –4 mA (CMOS) 3.7 3.7 V IOH = –6 mA (CMOS) 3.84 V IOH = –10 mA (TTL) 3 2.40 V VOL 1,2 LOW Level Output IOL = +6 mA (CMOS) 0.33 0.4 0.4 V IOL = +12 mA (TTL) 3 0.50 V VIH HIGH Level Input TTL Inputs 2.0 VCC + 0.3 2.0 VCC + 0.3 2.0 VCC + 0.3 V VIL LOW Level Input TTL Inputs –0.3 0.8 –0.3 0.8 –0.3 0.8 V IIN Input Leakage VI = VCC or GND –10 +10 –10 +10 –10 +10 µA IOZ 3-state Output Leakage VO = VCC or GND –10 +10 –10 +10 –10 +10 µA CIO I/O Capacitance3,4 10 10 10 pF ICC(S) Standby VCC Supply Current (typical = 0.7 mA) 2 10 20 mA ICC(D) Dynamic VCC Supply Current See “Power Dissipation” Section Notes: 1. Actel devices can drive and receive either CMOS or TTL signal levels. No assignment of I/Os as TTL or CMOS is required. 2. Tested one output at a time, VCC = min. 3. Not tested, for information only. 4. VOUT = 0V, f = 1 MHz. 5. Typical standby current = 0.7 mA. All outputs unloaded. All inputs = VCC or GND. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |