전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

LTC2923IDE 데이터시트(PDF) 9 Page - Linear Technology

부품명 LTC2923IDE
상세설명  Power Supply Tracking Controller
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  LINER [Linear Technology]
홈페이지  http://www.linear.com
Logo LINER - Linear Technology

LTC2923IDE 데이터시트(HTML) 9 Page - Linear Technology

Back Button LTC2923IDE Datasheet HTML 5Page - Linear Technology LTC2923IDE Datasheet HTML 6Page - Linear Technology LTC2923IDE Datasheet HTML 7Page - Linear Technology LTC2923IDE Datasheet HTML 8Page - Linear Technology LTC2923IDE Datasheet HTML 9Page - Linear Technology LTC2923IDE Datasheet HTML 10Page - Linear Technology LTC2923IDE Datasheet HTML 11Page - Linear Technology LTC2923IDE Datasheet HTML 12Page - Linear Technology LTC2923IDE Datasheet HTML 13Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 20 page
background image
LTC2923
9
2923fa
Figure 6. Simplified Functional Diagram
The LTC2923 features an electronic circuit breaker func-
tion that protects the optional series FET against short
circuits. When the FET is fully enhanced (GATE > RAMP +
4.9V), the electronic circuit breaker is enabled. Then, if the
voltage across the FET (VDS) exceeds 200mV as measured
from VCC to the RAMP pin for more than about 10µs the
gate of the FET is pulled down with 20mA, turning it off.
Because the slaved supplies track the RAMP pin, they are
pulled low by the tracking circuit when a short-circuit fault
occurs. Following a short-circuit fault, the FET is latched
off until the fault is cleared by pulling the ON pin below
0.4V.
Ramp Buffer
The RAMPBUF pin provides a buffered version of the
RAMP pin voltage that drives the resistive dividers on the
TRACKx pins. When there is no external FET, it provides up
to 2mA to drive the resistors even though the GATE pin
only supplies 10µA. The RAMPBUF pin also proves useful
in systems with an external FET. Since the track cell in the
simplified functional diagram above drives 0.8V on the
TRACKx pins, if RTBx is connected directly to the FET’s
source, the TRACKx pin could potentially pull up the FET’s
source towards 0.8V when the FET is off. RAMPBUF
blocks this path.
APPLICATIO S I FOR ATIO
–
+
–
+
–
+
+ –
VCC
200mV
GATE
Q1
MASTER
SLAVE1
SLAVE2
CGATE
1.2V
ON
RAMPBUF
10µA
VCC
VCC
VCC
RONB
RONA
RTA1
RTB1
RTA2
RTB2
10µA
RAMP
FB1
TRACK1
0.8V
–
+
FB2
TRACK2
0.8V
RFA1
RFB1
DC/DC
RFA2
2923 F06
RFB2
DC/DC
1×



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com