| 전자부품 데이터시트 검색엔진 |
|
OP37CFK 데이터시트(PDF) 16 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
OP37CFK 데이터시트(HTML) 16 Page - Texas Instruments |
|
16 / 21 page ![]() OP27A, OP27C, OP27E, OP27G OP37A, OP37C, OP37E, OP37G LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS SLOS100B – FEBRUARY 1989 – REVISED AUGUST 1994 2–16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 TYPICAL CHARACTERISTICS OP37 VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE 80 60 40 20 0 – 20 – 40 – 60 – 80 t – Time – µs 0 0.2 0.4 0.6 0.8 1 1.2 VCC ± = ±15 V AV = 5 CL = 15 pF TA = 25°C OP37 VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 8 6 4 0 – 2 – 4 – 6 – 8 2 t – Time – µs 012 345 6 VCC ± = ±15 V AV = 5 TA = 25°C Figure 32 Figure 33 APPLICATION INFORMATION general The OP27 and OP37 series devices can be inserted directly onto OP07, OP05, µA725, and SE5534 sockets with or without removing external compensation or nulling components. In addition, the OP27 and OP37 can be fitted to µA741 sockets by removing or modifying external nulling components. noise testing Figure 34 shows a test circuit for 0.1-Hz to 10-Hz peak-to-peak noise measurement of the OP27 and OP37. The frequency response of this noise tester indicates that the 0.1-Hz corner is defined by only one zero. Because the time limit acts as an additional zero to eliminate noise contributions from the frequency band below 0.1 Hz, the test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds. Measuring the typical 80-nV peak-to-peak noise performance of the OP27 and OP37 requires the following special test precautions: 1. The device should be warmed up for at least five minutes. As the operational amplifier warms up, the offset voltage typically changes 4 µV due to the chip temperature increasing from 10°C to 20°C starting from the moment the power supplies are turned on. In the 10-s measurement interval, these temperature-induced effects can easily exceed tens of nanovolts. 2. For similar reasons, the device should be well shielded from air currents to eliminate the possibility of thermoelectric effects in excess of a few nanovolts, which would invalidate the measurements. 3. Sudden motion in the vicinity of the device should be avoided, as it produces a feedthrough effect that increases observed noise. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |