전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

TL16C752 데이터시트(PDF) 28 Page - Texas Instruments

부품명 TL16C752
상세설명  3.3-V DUAL UART WITH 64-BYTE FIFO
PDF  33 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  TI [Texas Instruments]
홈페이지  http://www.ti.com
Logo TI - Texas Instruments

TL16C752 데이터시트(HTML) 28 Page - Texas Instruments

Back Button TL16C752 Datasheet HTML 24Page - Texas Instruments TL16C752 Datasheet HTML 25Page - Texas Instruments TL16C752 Datasheet HTML 26Page - Texas Instruments TL16C752 Datasheet HTML 27Page - Texas Instruments TL16C752 Datasheet HTML 28Page - Texas Instruments TL16C752 Datasheet HTML 29Page - Texas Instruments TL16C752 Datasheet HTML 30Page - Texas Instruments TL16C752 Datasheet HTML 31Page - Texas Instruments TL16C752 Datasheet HTML 32Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 28 / 33 page
background image
TL16C752
3.3-V DUAL UART WITH 64-BYTE FIFO
SLLS305 – MAY 1999
28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
interrupt enable register (IER)
The interrupt enable register (IER) enables each of the six types of interrupt, receiver error, RHR interrupt, THR
interrupt, Xoff received or CTS/RTS change of state from low to high. The INT output signal is activated in
response to interrupt generation. Table 14 shows interrupt enable register bit settings.
Table 14. Interrupt Enable Register (IER) Bit Settings
BIT NO.
BIT SETTINGS
0
0 = Disable the RHR interrupt
1 = Enable the RHR interrupt
1
0 = Disable the THR interrupt
1 = Enable the THR interrupt
2
0 = Disable the receiver line status interrupt
1 = Enable the receiver line status interrupt
3
0 = Disable the modem status register interrupt
1 = Enable the modem status register interrupt
4
0 = Disable sleep mode
1 = Enable sleep mode
5
0 = Disable the Xoff interrupt
1 = Enable the Xoff interrupt.
6
0 = Disable the RTS interrupt
1 = Enable the RTS interrupt
7
0 = Disable the CTS interrupt
1 = Enable the CTS interrupt
NOTE: IER[7:4] can only be modified if EFR[4] is set, i.e., EFR[4] is a write enable.
Re-enabling IER[1] will not cause a new interrupt until new data has been
written to the TX FIFO.
interrupt identification register (IIR)
The IIR is a read-only 8-bit register which provides the source of the interrupt in a prioritized manner. Table 15
shows interrupt identification register bit settings.
Table 15. Interrupt Identification Register (IIR) Bit Settings
BIT NO.
BIT SETTINGS
0
0 = A interrupt is pending
1 = No interrupt is pending
3:1
3-Bit encoded interrupt. See Table 14.
4
1 = Xoff/Special character has been detected.
5
CTS/RTS low to high change of state.
7:6
Mirror the contents of FCR[0]



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com