전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

TMS279X 데이터시트(PDF) 29 Page - Texas Instruments

부품명 TMS279X
상세설명  FLOPPY DISK FORMATTERICONTROLLER FAMILY
PDF  40 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  TI [Texas Instruments]
홈페이지  http://www.ti.com
Logo TI - Texas Instruments

TMS279X 데이터시트(HTML) 29 Page - Texas Instruments

Back Button TMS279X Datasheet HTML 25Page - Texas Instruments TMS279X Datasheet HTML 26Page - Texas Instruments TMS279X Datasheet HTML 27Page - Texas Instruments TMS279X Datasheet HTML 28Page - Texas Instruments TMS279X Datasheet HTML 29Page - Texas Instruments TMS279X Datasheet HTML 30Page - Texas Instruments TMS279X Datasheet HTML 31Page - Texas Instruments TMS279X Datasheet HTML 32Page - Texas Instruments TMS279X Datasheet HTML 33Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 29 / 40 page
background image
TMS279X (WD279X) FLOPPY DISK FORMATTER / CONTROLLER FAMILY
29
status register
Upon receipt of any command, except the Force Interrupt command, the busy status bit is set and the rest of
the status bits are updated or cleared for the new command. If the Force Interrupt command is received
when there is a current command under execution, the busy status bit is reset, and the reset of the status
bits are unchanged. If the Force Interrupt command is received when there is not a current command under
execution, the busy status bit is reset and the rest of the status bits are updated or cleared. In this case,
status reflects the Type I commands.
The user has the option of reading the status register through program control or using the DRQ line with
DMA or interrupt methods. When the data register is read, the DRQ bit in the status register and the DRQ
line are automatically reset. A write to the data register also causes both DRQ's to reset.
The busy bit in the status may be monitored with a user program to determine when a command is complete,
in lieu of using the INTRQ line. When using the INTRQ, a busy status check is not recommended because a
read of the status register to determine the condition of busy will reset the INTRQ line.
The format of the status register is shown below:
(BITS)
7
6
5
4
3
2
1
0
S7
S6
S5
S4
S3
S2
S1
S0
Status varies according to the type of command executed as shown in Table 4.
Because of internal sync cycles, certain time delays must be observed when operating under programmed
1/0. They are: (times double when clock = 1 MHz).
OPERATION
NEXT OPERATION
DELAY REG’D
FM
MFM
Write to Command Register
Write to Command Register
Write Any Register
Read Busy Bit (Status Bit 0)
Read Status Bits 1-7
Read from Different Register
12 µs
28 µs
0
6 µs
14 µs
0
IBM 3740 format - 128 bytes/sector
Shown below is the IBM single-density format with 128 bytes/sector. In order to format a diskette, the user
must issue the Write Track command, and load the data register with the following values. For every byte to
be written, there is one data request.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com