• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400

• India Tel: +91.80.4155721

• China Tel: +86.21.2407.1588

Visit www.macomtech.com for additional data sheets and product information.

M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make

changes to the product(s) or information contained herein without notice.

2

GaAs SPDT Reflective Switch with TTL/CMOS Control Input,

DC-3.0 GHz

Rev. V6

SW-110-PIN

ADVANCED:

Data Sheets contain information regarding a product M/A-COM Technology Solutions

is considering for development. Performance is based on target specifications, simulated results,

and/or prototype measurements. Commitment to develop is not guaranteed.

PRELIMINARY:

Data Sheets contain information regarding a product M/A-COM Technology

Solutions has under development. Performance is based on engineering tests. Specifications are

typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.

Commitment to produce in volume is not guaranteed.

1,2,3

Parameter

Frequency

Units

Min

Typ

Max

Reference

Insertion Loss

DC - 0.5 GHz

DC - 1.0 GHz

DC - 2.0 GHz

DC - 3.0 GHz

dB

dB

dB

dB

—

—

—

—

—

—

—

—

0.6

0.7

0.9

1.1

Isolation

DC - 0.5 GHz

DC - 1.0 GHz

DC - 2.0 GHz

DC - 3.0 GHz

dB

dB

dB

dB

40

35

24

18

—

—

—

—

—

—

—

—

VSWR

DC - 0.5 GHz

DC - 1.0 GHz

DC - 2.0 GHz

DC - 3.0 GHz

Ratio

Ratio

Ratio

Ratio

—

—

—

—

—

—

—

—

1.2:1

1.4:1

1.4:1

1.5:1

Trise, Tfall

Ton, Toff

Transients

—

—

—

nS

nS

mV

—

—

—

12

35

30

—

—

—

1 dB Compression

0.9 GHz

0.9 GHz

0.9 GHz

0.9 GHz

dBm

dBm

dBm

dBm

—

—

—

—

+32.5

+32.5

+32.5

+39.5

—

—

—

—

0.9 GHz

0.9 GHz

dBm

dBm

—

—

+61

+65

—

—

Vcc

Vee

—

—

V

V

4.5

-8.0

5.0

—

5.5

-5.0

Icc

—

mA

—

—

1.0

Iee

—

mA

—

—

1.0

Test Conditions

—

—

—

10% to 90%

1.3V Control to 90/10% RF

In-band (peak-peak)

Input Power, 0.1 dB, -5V Control

Input Power, 1.0 dB, -5V Control

Input Power, 0.1 dB, -8V Control

Input Power, 1.0 dB, -8V Control

For two-tone Input power up to +10

dBm

-5V Control

-8V Control

Vcc = 4.5 to 5.5V

Vctl = 0 to 0.8V, or VCC - 2.1V to

VCC

Vee = -5.0 to –8.0V

Vctl

Vctl

Logic 0 (TTL)

Logic 1 (TTL)

—

—

V

V

0.0

2.0

—

—

0.8

5.0

Input Leakage

Current (Low)

0 to 0.8V

—

µA

—

—

1.0

Input Leakage

Current (High)

2.0 to 5.0V

—

µA

—

—

1.0

1. All specifications apply when operated with bias voltages of +5V for Vcc and –5.0V to –8.0V for Vee, and 50 Ohm impedance at all RF

ports unless otherwise specified.

2. For this switch to meet the guaranteed specifications, it is necessary to have a DC return on either RF1 or RF2. The DC return can be

either a 10k Ohm resistor, or an RF choke.

3. High Power (greater than 1W) handling specifications apply to cold switching only. For input powers under 1W, hot switching can be

used.