PIC18F44J10 datasheet(97/368 Pages) MICROCHIP

97 / 368 page

DS39682E-page 95

PIC18F45J10 FAMILY

9.6

INTx Pin Interrupts

External interrupts on the RB0/INT0, RB1/INT1 and

RB2/INT2 pins are edge-triggered. If the corresponding

INTEDGx bit in the INTCON2 register is set (= 1), the

interrupt is triggered by a rising edge; if the bit is clear,

the trigger is on the falling edge. When a valid edge

appears on the RBx/INTx pin, the corresponding flag

bit, INTxIF, is set. This interrupt can be disabled by

clearing the corresponding enable bit, INTxIE. Flag bit,

INTxIF, must be cleared in software in the Interrupt

Service Routine before re-enabling the interrupt.

All external interrupts (INT0, INT1 and INT2) can

wake-up the processor from the power-managed

modes if bit INTxIE was set prior to going into the

power-managed modes. If the Global Interrupt Enable

bit, GIE, is set, the processor will branch to the interrupt

vector following wake-up.

Interrupt priority for INT1 and INT2 is determined by the

value contained in the interrupt priority bits, INT1IP

(INTCON3<6>) and INT2IP (INTCON3<7>). There is

no priority bit associated with INT0. It is always a

high-priority interrupt source.

9.7

TMR0 Interrupt

In 8-bit mode (which is the default), an overflow in the

TMR0 register (FFh

→ 00h) will set flag bit, TMR0IF. In

16-bit mode, an overflow in the TMR0H:TMR0L register

pair (FFFFh

→ 0000h) will set TMR0IF. The interrupt

can be enabled/disabled by setting/clearing enable bit,

TMR0IE (INTCON<5>). Interrupt priority for Timer0 is

determined by the value contained in the interrupt prior-

ity bit, TMR0IP (INTCON2<2>). See Section 11.0

“Timer0 Module”

for further details on the Timer0

module.

9.8

PORTB Interrupt-on-Change

An input change on PORTB<7:4> sets flag bit, RBIF

(INTCON<0>). The interrupt can be enabled/disabled

by setting/clearing enable bit, RBIE (INTCON<3>).

Interrupt priority for PORTB interrupt-on-change is

determined by the value contained in the interrupt

priority bit, RBIP (INTCON2<0>).

9.9

Context Saving During Interrupts

During interrupts, the return PC address is saved on

the stack. Additionally, the WREG, STATUS and BSR

registers are saved on the Fast Return Stack. If a fast

return from interrupt is not used (see Section 6.3

“Data Memory Organization”

), the user may need to

save the WREG, STATUS and BSR registers on entry

to the Interrupt Service Routine. Depending on the

user’s application, other registers may also need to be

saved. Example 9-1 saves and restores the WREG,

STATUS and BSR registers during an Interrupt Service

Routine.

EXAMPLE 9-1:

SAVING STATUS, WREG AND BSR REGISTERS IN RAM

MOVWF

W_TEMP

; W_TEMP is in virtual bank

MOVFF

STATUS, STATUS_TEMP

; STATUS_TEMP located anywhere

MOVFF

BSR, BSR_TEMP

; BSR_TMEP located anywhere

;

; USER ISR CODE

;

MOVFF

BSR_TEMP, BSR

; Restore BSR

MOVF

W_TEMP, W

; Restore WREG

MOVFF

STATUS_TEMP, STATUS

; Restore STATUS

PIC18F44J10 데이터시트(PDF) 97 Page - Microchip Technology

PIC18F44J10 데이터시트(HTML) 97 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL