ATmega16 datasheet(103/357 Pages) ATMEL

103 / 357 page

103

2466S–AVR–05/09

ATmega16(L)

Figure 46. Fast PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV1) is set each time the counter reaches TOP. In addition

the OC1A or ICF1 Flag is set at the same timer clock cycle as TOV1 is set when either OCR1A

or ICR1 is used for defining the TOP value. If one of the interrupts are enabled, the interrupt han-

dler routine can be used for updating the TOP and compare values.

When changing the TOP value the program must ensure that the new TOP value is higher or

equal to the value of all of the Compare Registers. If the TOP value is lower than any of the

Compare Registers, a compare match will never occur between the TCNT1 and the OCR1x.

Note that when using fixed TOP values the unused bits are masked to zero when any of the

OCR1x Registers are written.

The procedure for updating ICR1 differs from updating OCR1A when used for defining the TOP

value. The ICR1 Register is not double buffered. This means that if ICR1 is changed to a low

value when the counter is running with none or a low prescaler value, there is a risk that the new

ICR1 value written is lower than the current value of TCNT1. The result will then be that the

counter will miss the compare match at the TOP value. The counter will then have to count to the

MAX value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur.

The OCR1A Register however, is double buffered. This feature allows the OCR1A I/O location

to be written anytime. When the OCR1A I/O location is written the value written will be put into

the OCR1A Buffer Register. The OCR1A Compare Register will then be updated with the value

in the Buffer Register at the next timer clock cycle the TCNT1 matches TOP. The update is done

at the same timer clock cycle as the TCNT1 is cleared and the TOV1 Flag is set.

Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using

ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However,

if the base PWM frequency is actively changed (by changing the TOP value), using the OCR1A

as TOP is clearly a better choice due to its double buffer feature.

In fast PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins.

Setting the COM1x1:0 bits to 2 will produce a non-inverted PWM and an inverted PWM output

can be generated by setting the COM1x1:0 to 3 (See Table 44 on page 110). The actual OC1x

value will only be visible on the port pin if the data direction for the port pin is set as output

(DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x Register at

the compare match between OCR1x and TCNT1, and clearing (or setting) the OC1x Register at

the timer clock cycle the counter is cleared (changes from TOP to BOTTOM).

TCNTn

OCRnx / TOP Update and

TOVn Interrupt Flag Set and

OCnA Interrupt Flag Set

(Interrupt on TOP)

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

ATmega16 데이터시트(PDF) 103 Page - ATMEL Corporation

ATmega16 데이터시트(HTML) 103 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL