ATmega169P datasheet(245/393 Pages) ATMEL

245 / 393 page

245

8018N–AVR–08/09

ATmega169P

23.5

LCD Register Description

23.5.1

LCDCRA – LCD Control and Status Register A

• Bit 7 – LCDEN: LCD Enable

Writing this bit to one enables the LCD Controller/Driver. By writing it to zero, the LCD is turned

off immediately. Turning the LCD Controller/Driver off while driving a display, enables ordinary

port function, and DC voltage can be applied to the display if ports are configured as output. It is

recommended to drive output to ground if the LCD Controller/Driver is disabled to discharge the

display.

• Bit 6 – LCDAB: LCD Low Power Waveform

When LCDAB is written logic zero, the default waveform is output on the LCD pins. When

LCDAB is written logic one, the Low Power Waveform is output on the LCD pins. If this bit is

modified during display operation the change takes place at the beginning of a new frame.

• Bit 5 – Res: Reserved Bit

This bit is reserved and will always read as zero.

• Bit 4 – LCDIF: LCD Interrupt Flag

This bit is set by hardware at the beginning of a new frame, at the same time as the display data

is updated. The LCD Start of Frame Interrupt is executed if the LCDIE bit and the I-bit in SREG

are set. LCDIF is cleared by hardware when executing the corresponding Interrupt Handling

Vector. Alternatively, writing a logical one to the flag clears LCDIF. Beware that if doing a Read-

Modify-Write on LCDCRA, a pending interrupt can be disabled. If Low Power Waveform is

selected the Interrupt Flag is set every second frame.

• Bit 3 – LCDIE: LCD Interrupt Enable

When this bit is written to one and the I-bit in SREG is set, the LCD Start of Frame Interrupt is

enabled.

• Bit 2 – LCDBD: LCD Buffer Disable

The intermediate voltage levels in the LCD are generated by an internal resistive voltage divider

and passed through buffer to increase the current driving capability. By writing this bit to one the

buffers are turned off and bypassed, resulting in decreased power consumption. The total resis-

tance of the voltage divider is nominally 400 k

Ω between LCDCAP and GND.

• Bit 1 – LCDCCD: LCD Contrast Control Disable

Writing this bit to one disables the internal power supply for the LCD driver. The desired voltage

must be applied to the LCDCAP pin from an external power supply. To avoid conflict between

internal and external power supply, this bit must be written as '1' prior to or simultaneously with

writing '1' to the LCDEN bit.

Bit

(0xE4)

LCDEN

LCDAB

–

LCDIF

LCDIE

LCDBD

LCDCCD

LCDBL

LCDCRA

Read/Write

R/W

Initial Value

ATmega169P 데이터시트(PDF) 245 Page - ATMEL Corporation

ATmega169P 데이터시트(HTML) 245 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL