ATmega169P datasheet(328/393 Pages) ATMEL

328 / 393 page

328

8018N–AVR–08/09

ATmega169P

Note:

1. “Max” means the highest value where the pin is guaranteed to be read as low

2. “Min” means the lowest value where the pin is guaranteed to be read as high

3. Although each I/O port can sink more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V for Port B and 10 mA

at V

CC = 5V, 5 mA at VCC = 3V for all other ports) under steady state conditions (non-transient), the following must be

observed:

TQFP and QFN/MLF Package:

1] The sum of all IOL, for all ports, should not exceed 400 mA.

2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.

3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.

4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.

5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.

If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test condition.

4. Although each I/O port can source more than the test conditions (20 mA at V

CC = 5V, 10 mA at VCC = 3V for Port B and 10mA

at VCC = 5V, 5 mA at VCC = 3V for all other ports) under steady state conditions (non-transient), the following must be

observed:

TQFP and QFN/MLF Package:

1] The sum of all IOH, for all ports, should not exceed 400 mA.

2] The sum of all IOH, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.

3] The sum of all IOH, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.

4] The sum of all IOH, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.

5] The sum of all IOH, for ports F0 - F7, should not exceed 100 mA.

If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current

greater than the listed test condition.

5. All bits set in the “Power Reduction Register” on page 34.

6. Typical values at 25

°C. Maximum values are characterized values and not test limits in production.

ICC

Power Supply Current(5)

Active 1 MHz, VCC = 2V

0.35

0.44

Active 4 MHz, VCC = 3V

2.3

2.5

Active 8 MHz, VCC = 5V

8.4

9.5

Idle 1 MHz, VCC = 2V

0.1

0.2

Idle 4 MHz, VCC = 3V

0,7

0.8

Idle 8 MHz, VCC = 5V

3.0

3.3

Power-save mode(6)

32 kHz TOSC enabled,

VCC = 1.8V

0.55

1.6

µA

32 kHz TOSC enabled,

VCC = 3V

0.8

2.6

µA

Power-down mode(6)

WDT enabled, VCC = 3V

µA

WDT disabled, VCC = 3V

0.2

µA

VACIO

Analog Comparator

Input Offset Voltage

VCC = 5V

Vin = VCC/2

<10

IACLK

Analog Comparator

Input Leakage Current

VCC = 5V

Vin = VCC/2

-50

tACPD

Analog Comparator

Propagation Delay

VCC = 2.7V

VCC = 4.0V

750

500

A = -40°C to 85°C, VCC = 1.8V to 5.5V (unless otherwise noted) (Continued)

Symbol

Parameter

Condition

Min.

Typ.

Max.

Units

ATmega169P 데이터시트(PDF) 328 Page - ATMEL Corporation

ATmega169P 데이터시트(HTML) 328 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL