ATmega325P datasheet(223/364 Pages) ATMEL

223 / 364 page

223

8023F–AVR–07/09

ATmega325P/3250P

22. JTAG Interface and On-chip Debug System

22.1

Features

• JTAG (IEEE std. 1149.1 Compliant) Interface

• Boundary-scan Capabilities According to the IEEE std. 1149.1 (JTAG) Standard

• Debugger Access to:

– All Internal Peripheral Units

– Internal and External RAM

– The Internal Register File

–Program Counter

– EEPROM and Flash Memories

• Extensive On-chip Debug Support for Break Conditions, Including

– AVR Break Instruction

– Break on Change of Program Memory Flow

– Single Step Break

– Program Memory Break Points on Single Address or Address Range

– Data Memory Break Points on Single Address or Address Range

• Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface

• On-chip Debugging Supported by AVR Studio®

22.2

Overview

The AVR IEEE std. 1149.1 compliant JTAG interface can be used for

• Testing PCBs by using the JTAG Boundary-scan capability

• Programming the non-volatile memories, Fuses and Lock bits

• On-chip debugging

A brief description is given in the following sections. Detailed descriptions for Programming via

the JTAG interface, and using the Boundary-scan Chain can be found in the sections ”Program-

ming via the JTAG Interface” on page 291 and ”IEEE 1149.1 (JTAG) Boundary-scan” on page

229, respectively. The On-chip Debug support is considered being private JTAG instructions,

and distributed within ATMEL and to selected third party vendors only.

Figure 22-1 shows a block diagram of the JTAG interface and the On-chip Debug system. The

TAP Controller is a state machine controlled by the TCK and TMS signals. The TAP Controller

selects either the JTAG Instruction Register or one of several Data Registers as the scan chain

(Shift Register) between the TDI – input and TDO – output. The Instruction Register holds JTAG

instructions controlling the behavior of a Data Register.

The ID-Register, Bypass Register, and the Boundary-scan Chain are the Data Registers used

for board-level testing. The JTAG Programming Interface (actually consisting of several physical

and virtual Data Registers) is used for serial programming via the JTAG interface. The Internal

Scan Chain and Break Point Scan Chain are used for On-chip debugging only.

22.3

TAP – Test Access Port

The JTAG interface is accessed through four of the AVR’s pins. In JTAG terminology, these pins

constitute the Test Access Port – TAP. These pins are:

• TMS: Test mode select. This pin is used for navigating through the TAP-controller state

machine.

• TCK: Test Clock. JTAG operation is synchronous to TCK.

ATmega325P 데이터시트(PDF) 223 Page - ATMEL Corporation

ATmega325P 데이터시트(HTML) 223 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL