MCP1790 datasheet(6/34 Pages) MICROCHIP

6 / 34 page

MCP1790/MCP1791

DS22075A-page 6

Detect Threshold to PWRGD Active

Time Delay

TVDET-PWRG

—

235

—

µs

VOUT = VPWRGD_TH +

100 mV to VPWRGD_TH -

100 mV

AC Performance

Output Delay From SHDN

TOR

—

200

—

µs

SHDN = GND to VIN,

VOUT = GND to 95% VR,

COUT = 1.0 µF

PWRGD Delay from SHDN

TSHDN_PG

—

400

—

SHDN = VIN to GND,

COUT = 1.0 µF

Output Noise

—1.2

—

µV/

√Hz) I

OUT = 50 mA, f = 1 kHz

Power Supply Ripple Rejection Ratio

PSRR

VIN = 7.0V, CIN = 0 µF,

IOUT = 10 mA,

VINAC = 400 mVpp

—

f = 100 Hz

—

f = 1 kHz, VR = 5.0V

—

f = 1 kHz, VR = < 5.0V

Thermal Shutdown Temperature

TSD

—

157

—

°C

Rising Temperature

Thermal Shutdown Hysteresis

ΔT

—

°C

Falling Temperature

Short Circuit Recovery Time

tTHERM

—0

—

(Note 8)

AC/DC CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise noted, V

IN = VOUT(MAX) + VDROPOUT(MAX), (Note 1), IOUT = 1 mA,

COUT = 4.7 µF (X7R Ceramic), CIN = 4.7 µF (X7R Ceramic), TA = +25°C, SHDN > 2.4V.

Boldface type applies for junction temperatures, T

J (Note 5) of -40°C to +125°C.

Parameters

Symbol

Min

Typ

Max

Units

Conditions

Note 1:

The minimum VIN, VIN(MIN) must meet two conditions: VIN ≥ 6.0V and VIN ≥ VOUT(MAX) + VDROPOUT(MAX).

VR is the nominal regulator output voltage.

Load regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is

tested over a load range from 1 mA to the maximum specified output current.

The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction

temperature and the thermal resistance from junction to air. (i.e., TA, TJ, θJA). Exceeding the maximum allowable power

dissipation will cause the device operating junction temperature to exceed the maximum 165°C rating. Sustained

junction temperatures above 165°C can impact the device reliability.

The junction temperature is approximated by soaking the device under test at an ambient temperature equal to the

desired Junction temperature. The test time is small enough such that the rise in the Junction temperature over the

ambient temperature is not significant.

Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its

nominal value that was measured with an input voltage of VIN = VR + VDROPOUT(MAX).

Sustained junction temperatures above 165°C can impact the device reliability.

The Short Circuit Recovery Time test is done by placing the device into a short circuit condition and then removing the

short circuit condition before the device die temperature reaches 125 °C. If the device goes into thermal shutdown, then

the Short Circuit Recovery Time will depend upon the thermal dissipation properties of the package and circuit board.

TCVOUT = (VOUT-HIGH - VOUT-LOW) *10^6 / (VR * ΔTemperature), VOUT-HIGH = highest voltage measured over the tem-

peraturerange. VOUT-LOW = lowest voltage measured over the temperature range.

MCP1790 데이터시트(PDF) 6 Page - Microchip Technology

MCP1790 데이터시트(HTML) 6 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

데이터시트 다운로드

링크 URL